Perkins 402D Скачать руководство пользователя страница 79

Страница: 79 / 98

This document is printed from SPI². Not for RESALE

SEBU8311-02

Maintenance Section

Fuel System - Prime

NOTICE

If a fuel injector is suspected of operating outside of

normal parameters it should be removed by a quali

technician. The suspect fuel injector should be taken

to an authorised agent for inspection.

Operate the engine at a fast idle speed in order to

identify the faulty fuel injector. Individually loosen

and tighten the union nut for the high pressure pipe

to each fuel injector. Do not loosen the union nut

more than half a turn. There will be little effect on the

engine speed when the union nut to the faulty fuel

injector is loosened.

Consult your authorized Perkins dealer or your

Perkins distributor for further assistance.

i02596360

Fuel System - Prime

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting, and repair of the product. Be prepared

to collect the

uid with suitable containers before

opening any compartment or disassembling any com-

ponent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

Use the following procedure in order to prime the fuel

system:

If air enters the fuel system, the air must be purged

from the fuel system before the engine can be

started. Air can enter the fuel system when the

following events occur:

•

The fuel tank is empty or the fuel tank has been

partially drained.

•

The low pressure fuel lines are disconnected.

•

A leak exists in the low pressure fuel system.

•

The fuel

lter is replaced.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting, and repair of the product. Be prepared

to collect the

uid with suitable containers before

opening any compartment or disassembling any com-

ponent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

Primary

lter

Ensure that the air is removed from the primary

lter

before you prime the fuel

lters. Refer to illustration

49.

g01316878

Illustration 49
This

lter may not be installed on the engine.

(1) Vent screws

Fuel

lters

There are three types of fuel

lter that may be

installed on the engine.

•

Element

•

Canister

•

Spin-on

lter with fuel priming pump

Содержание 402D


































































































Результаты поиска

Содержание 402D

Отзывы:

Perkins 402D, Руководство по эксплуатации и обслуживанию, Страница: 79 / 98

Результаты поиска

Содержание 402D

Отзывы: