background image

Assembly and Operation Manual  

5.5.3 Control over the turnstile is effected by input of the control signal to the turnstile at 
both control modes. The passage waiting time in the pulse control mode is 5 seconds 
regardless of the control signal length. In the potential control mode the passage waiting 
time equals the length of the control signal. 
5.5.4 The pulse control mode is intended for the turnstile operation from the RC panel, 
WRC or the ACS controller,

 

outputs of which support the pulse control mode. 

Standard control inputs: Unl

ock 

A, 

Stop

 and 

Unlock B

.  

Special control input: 

Fire Alarm

.  

See Table 2 for the turnstile operating modes at this control mode. 
The algorithm of control signals at this mode is stipulated in Appendix A. 
The minimum input signal duration, when the operating mode can be changed, should be 
100 ms. The passage waiting time is 5 sec. and it does not depend on the input signal 
duration. 
See Clause 5.10. for the turnstile operation at special “Fire Alarm” control input. 
5.5.5 The potential control mode is intended for the turnstile operation from the ACS 
controller,

 

outputs of which support the potential control mode

 

(for example,

 

a lock 

controller). 

Standard control inputs: 

Unlock A

 and 

Unlock B

Special control inputs: 

Stop

 and 

Fire Alarm

See Table 2 for the turnstile operating modes at this control mode. 
The algorithm of control signals at this mode is stipulated in Appendix B. 
The minimum input signal duration, when the operating mode can be changed, should be 
100msec. The passage waiting time is equal to the low-level signal duration (the turnstile 
remains open in the set direction if a low-level signal exists at the set direction input by the 
moment of passage).  
At the low-level signal inputting to the

 

Stop

 

input,

 

both directions are locked for the time of 

the signal duration regardless the signal strength at the inputs

 

Unlock

 

A

 

and

 

Unlock

 

B

”. 

At the low-level signal removing from the “

Stop

” input, the directions are set to the control 

mode according to the signal strength at the inputs

 

Unlock

 

A

 

and “

Unlock B

”.  

See Clause 5.10 for the turnstile operation at the special “Fire Alarm” control input.  

5.6  Operation with the RC panel  

5.6.1 When the buttons on the RC panel are pressed (the

 STOP

 button and the two other 

buttons corresponding to the passage direction), the closing of the relevant contact “

Stop

”, 

Unlock A

” or “

Unlock B

” to the contact “

GND

” occurs (i.

е

. forming of the low-level signal 

relatively to the contact “

GND

”). 

5.6.2 Operation logic of the turnstile at the single passage in the 

А

(

В

) direction at the pulse 

control mode: 

5.6.2.1 When the button, corresponding to the 

А

 (

В

) passage direction, is pressed 

on the RC panel,

 

the closing of the contact

 

Unlock

 

A(

В

)”

 

to the contact

 

GND

 

occurs (i.

е

. forming of the low-level signal on the contact “

Unlock A(

В

)” relatively to 

the contact “

GND

”). 

5.6.2.2 The CLB microcontroller processes the incoming command and generates 
the command to the control mechanism, which opens the 

А

 (

В

) passage direction 

(lifts the upper (lower) edge of the key holt). 

12 

Содержание TTR-07.1



































Отзывы:

Похожие инструкции для TTR-07.1