PBN AIMA-FT5S Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 62

PBN AIMA-FT5S Скачать руководство пользователя страница 37

AIMA-FT5S

Product User Manual

Pacific Broadband Networks

18 July 2014

Page 37 of 62

6.3 Applying RF settings to FT5S transmitter AGC mode

Go to the “

Port 1

” or the “

Port 2

” section on the FT5S configuration page through the ASMM’s web

interface (see section 6.1 for details).

6.3.1 Sample RF load for 80 analog channels of RF load

Connect the RF load at a level of 15 dBmV ± 3 dB (80 analog channels) to the BC input of the FT5S

transmitter. If the BC port is only being used it is advised to terminate the NC port with a 75

Ω

terminator.

See the sample calculation for calculated RF input level (section 6.1.1. Example 1)

1.

Set the “

Input AGC Mode

” to “

ON

” and click “

Submit

” to apply all settings

Both transmitters have independent settings and they need to be adjusted separately.

6.3.2 Sample RF load for 42 analog channels of RF load

Connect the RF load at a level of 17.8 dBmV ± 3 dB (42 analog channels) to the BC input of the FT5S

transmitter. If the BC port is only being used it is advised to terminate the NC port with a 75

Ω

terminator.

See the sample calculation for calculated RF input level (section 6.1.1. Example 2)

1.

Set the “

Input AGC Mode

” to “

ON

” and click “

Submit

” to apply all settings

«
...
35
36
37
38
39
...
»

Содержание AIMA-FT5S































































Отзывы:

Нет отзывов