manualshive.com logo in svg

PBN AIMA-FT5S, Руководство пользователя, Страница: 23 / 62

Поделиться
Скачать
PBN AIMA-FT5S Скачать руководство пользователя страница 23

AIMA-FT5S

 Product User Manual

 

Pacific Broadband Networks 

18 July 2014 

Page 23 of 62 

DO NOT remove the dust cap from the fiber connector until right before connecting it 

to the input port.

 

4.  Raise the clip, insert the fiber connector, and then lower the clip over the connector. 

 

 

When using the sliding guide, put the fiber connector in the clip and slide it in from the rear to the front, 

through the chassis. Ensure that the optical fiber tail does not become trapped or pulled tightly.

 

 

Fiber clip (at rear, for up to two connectors)   

 

 

 

Handle (at front)  

5.4.2  Using the Fiber Tray 

All optical fibers must be organized in a tidy manner in the chassis’s fiber tray, which provides enough 

space  for  up  to  64  optical  fibers.  This  allows  for  easy  positioning  and  future  replacement  of  optical 

fibers. Along the front of the chassis, there are cut-outs for keeping the optical fibers in position.  

1.  When  organizing  the  optical  fibers,  lift  up  the  metal  flap  at  the  rear  of  the  panel  above  the 

sliding guide. This will allow fiber cables to be moved away from the sliding guide rails. 

 

Содержание AIMA-FT5S































































Отзывы:

Нет отзывов