PBN AIMA-FT5S Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 62

PBN AIMA-FT5S Скачать руководство пользователя страница 32

AIMA-FT5S

Product User Manual

Pacific Broadband Networks

18 July 2014

Page 32 of 62

6.1.1 Determine the RF power to the RF input port.

In order to set up the port configuration for the FT5S transmitter, the proper RF level must to be

determined and applied to the transmitter. The factory default RF load is listed below



Number of analog RF channels = 80



RF level for 80 channels = 15 dBmV



This ensures an OMI of 2% per channel

The channel load listed above is the reference RF load for the FT5S transmitter. Any deviation from

this RF load will require new RF levels to be calculated based on 80 analog channels for a designated

RF input level of 15 dBmV.

To recalculate the RF input level following formula can be used:

(Na) = number of channels to be used by the transmitter

Example

Example 1 is to verify the RF calculations. The standard channel load will be used to determine the

correct RF input at the transmitter for 80 channels.

Channel load is 80 analog channels

Peak analog input = 34

– 10 LOG (80)

Peak analog input = 34

– 19

Peak analog input =

15 dBmV

The calculated RF level is 15 dBmV as specified on the datasheet. .

PEAK analog RF input = 34

– 10 LOG (Na)

«
...
30
31
32
33
34
...
»

Содержание AIMA-FT5S































































Отзывы:

Нет отзывов