PBN AIMA-FT5S Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 62

PBN AIMA-FT5S Скачать руководство пользователя страница 27

AIMA-FT5S

Product User Manual

Pacific Broadband Networks

18 July 2014

Page 27 of 62

5.7 Test the Optical Output Signal

After the input signal has been confirmed, the optical power of the associated optical output port

should be tested. Use the optical power meter to test the output levels; the output values should be in

accordance with the technical specifications.

Before testing, the optical power meter must be calibrated. Before measuring optical signals, verify the

interfaces are clean and undamaged.

CAUTION!

The device output optical power measurement procedure and regular maintenance

must be performed by highly trained personnel. All procedures and maintenance

must be comply with the necessary safety precautions indicated with using any

optical transmitter module:

WARNING!

Module emits an invisible laser when working. Avoid direct contact with the laser

connector. DO NOT look directly at the fiber connector.

«
...
25
26
27
28
29
...
»

Содержание AIMA-FT5S































































Отзывы:

Нет отзывов