PBN AIMA-FT5S Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 62

PBN AIMA-FT5S Скачать руководство пользователя страница 21

AIMA-FT5S

Product User Manual

Pacific Broadband Networks

18 July 2014

Page 21 of 62

3. After the module is inserted, gently push the hinged tab until it snaps into the orange retaining

clip. While pushing down on the hinged tab, the AIMA module will mate with the power bus

and will lock in into the chassis

CAUTION!

If force is required to insert a module, then it may not be correctly

seated on the slide rails, or the mounting screw may be misaligned.

4. When the module is fully seated within the chassis, on the of the AIMA module, fasten the

spring-loaded mounting screw.

Only use fingers to fasten the mounting screw. DO NOT

use a screwdriver

5.4 Connecting Optical Cables

For the convenience of the user, the

AIMA3000 Chassis has a Sliding Fiber Guide to help the operator

to arrange the cables. For the specific steps to connect the fiber, please refer to the instructions in

section 5.4.1.

5.4.1 Using the Sliding Fiber Guide

The sliding fiber guide is located in the lower-left corner of the chassis if looking at the front of the

chassis, and is designed to help installation of the optical fiber cabling. To access the sliding fiber

guide you will need to first remove the rear panel located on the back of the chassis.

1. Unscrew the two thumbscrews on the rear panel.

«
...
19
20
21
22
23
...
»

Содержание AIMA-FT5S































































Отзывы:

Нет отзывов