PBN AIMA-FT5S Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 62

PBN AIMA-FT5S Скачать руководство пользователя страница 25

AIMA-FT5S

Product User Manual

Pacific Broadband Networks

18 July 2014

Page 25 of 62

5.4.3 Cleaning the Fiber Connector Ends and Front-panel Optical Ports

To obtain a good quality optical input signal, optical fiber input ports and fiber connector ends must be

carefully cleaned.

Figure 5-4

When cleaning the optical fiber-connector end, remove the dust cap and then use a lint-free cloth

dampened with a static dissipative solvent to clean the angled surface. Dry the surface using a dry lint-

free cloth.

To clean the front-panel optical port, use a special lint-free swab that is designed for this purpose.

Dampen it with a static dissipative solvent. Apply slight pressure to the internal angled surface of the

optical port, while rotating the swab 90 degrees back and forth. You may need to remove excess

solvent using a dry lint-free swab. Alternatively, a cleaning pen such as the one click cleaner can be

used.

Head face

Connection terminal

SC one click cleaning pen

www.oneclickcleaner.com

«
...
23
24
25
26
27
...
»

Содержание AIMA-FT5S































































Отзывы:

Нет отзывов