Ref.
/640
PM2006-V
8
-
PMS2000 System
-
4.2 Visualizzazione dei guasti
In caso di corto circuito della linea A o B (durante la diffusione
musicale) il PM2006-V esclude la zona (A+B); al successivo test
identifica la linea che ha provocato il corto circuito escludendola
e riabilitando la linea della zona non in corto.
Le linee/zone in corto sono visualizzate con lampeggio dei leds
gialli A/B, dal led giallo “SHORT” acceso e dal lampeggio del
corrispondnete led verde “PROGRAM INSERTION”.
Sul lato sinistro del pannello frontale, i led gialli FAULTS (
) e (
2
)
svolgono la funzione di visualizzazione dei guasti - se riscontrati
- durante il test. Ecco nel dettaglio la causa dell’accensione di
ciascun led e l’eventuale rimedio.
LeD
CaUSa DeL GUaStO / CaUSe OF FaiLURe
eVeNtUaLe RiMeDiO / ReMeDy, iF aNy
GND
Un’uscita da 1 a 6 è connessa a massa con una resistenza
inferiore a 20 k
W
.
Cercare la dispersione e risolvere il problema.
An output - from 1 to 6 is connected to earth with a
resistance of less than 20 k
W
.
Find the dispersion and solve the problem.
DC
É presente un guasto sui dispositivi di alimentazione della
scheda.
Rivolgersi ad un Centro Assistenza Paso.
There is a failure on the devices powering the card.
Contact a Paso Service Centre.
aC
É presente un guasto sulla linea di alimentazione AC.
Verificare il fusibile e la presenza del 220 V di rete.
There is a failure on the AC power line.
Check the fuse and presence of the mains 220 V power supply.
BatteRy
Manca il 24 V di alimentazione batteria (se impostato).
Provvedere all’alimentazione.
No 24 V power from the battery (if set).
Provide power.
SHORt
Un’uscita da 1 a 6 è in corto-circuito (con impedenza inferiore
a 10
W
: il led verde relativo alla linea intereressata dal guasto
lampeggia.
Risolvere il corto-circuito e premere il tasto corrispondente al led
verde lampeggiante per ripristinare la linea (oltre al led verde
lampeggiante, dopo il successivo giro di test si accenderà anche il
led di zona giallo ad indicare la bassa impedenza rilevata).
An output - from 1 to 6 - is short-circuited (with an impedance
of less than 10
W
: the green LED associated with the failed
line is flashing.
Solve the short circuit and press the key associated with the flashing
green LED to reinstate the line (in addition to the flashing green
LED, after the next test routine the yellow zone LED will also light
up to indicate the low impedance detected).
aMPLy
L’amplificatore VOICE è guasto.
Rivolgersi ad un Centro Assistenza Paso.
The VOICE amplifier has failed.
Contact a Paso Service Centre
SPaRe
L’amplificatore SPARE (riserva) è guasto.
Rivolgersi ad un Centro Assistenza Paso.
The SPARE (stand-by) amplifier has failed.
Contact a Paso Service Centre
iNSeRtiON
Amplificatore di riserva abilitato.
-
Stand-by amplifier enabled.
-
a
Stato dell’impedenza sulla linea A
(led fisso: imp. ALTA; led lampeggiante: imp. BASSA).
-
State of impedance on line A
(steady LED: HIGH impedance, flashing: LOW impedance).
-
B
Stato dell’impedenza sulla linea B
(led fisso: imp. ALTA; led lampeggiante: imp. BASSA).
-
State of impedance on line B
(steady LED: HIGH impedance, flashing: LOW).
-
4.2 Fault display
In the event of a short circuit of lines A or B (while broadcasting
music), the PM2006-V will exclude the zone concerned (A+B) and
during the next test routine, identifies the line that has caused the
short circuit, excluding it and re-enabling the line of the zone that is
not short-circuited. The short-circuited lines/zones are signalled as
follows: yellow A/B LEDs flashing, yellow “SHORT” LED illuminated
and corresponding green “PROGRAM INSERTION” LED flashing.
On the left side of the panel the yellow FAULTS LEDs (
) and (
2
)
have the purpose of displaying any failures detected during the
test. Following are the details of the causes for illuminating each
LED and the possible remedies.