Partlow MRC 7800 Скачать руководство пользователя страница 45

Страница: 45 / 57

AGE

Er8

- Cal2 Volt Input

1. Check that 100mVDC is properly connected to the

Error

instrument and is within the tolerance limts as

indicated in the CAL2 procedure of the Calibration

section (page 35).

2. Turn off the power to the instrument and open the

cover. Loosen the platen hold down screw and swing

the platen open. Inspect the Processor board

(Appendix A-1, page 46) to insure that the input

conditioning jumper JU4 is in the non-volt position.

The jumper must be in the non-volt position to perform

the

CAL2

procedure properly. Close the platen and

tighten the hold down screw. Close the cover and

turn on the power to the instrument.

3. Perform the

CAL2

procedure as described in the

Calibration section (page 35).

Er9

- ADC Reference

1. Perform the

CAL2

procedure as described in the

Number Error

Calibration section (page 35).

Er10

- ADC Reference

1. Perform the

CAL2

procedure as described in the

Voltage Error

Calibration section (page 35).

Er12

- CAL2 Voltage Error

1. Check that 100 mVDC is properly connected to the

instrument and is within the tolerance limits as

indicated in the

CAL2

procedure of the Calibration

section (page 35)

2. Turn off the power to the instrument and open the

cover. Loosen the platen hold down screw and swing

the platen open . Inspect the Processor board

(Appendix A-1, page 46) to insure that the input

conditioning jumper JU4 is in the non-volt position.

3. Perform the

CAL2

procedure as described in the

Calibration section (page 35).

Содержание MRC 7800


























































Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды

Partlow MRC 7800, Инструкция по установке, монтажу и эксплуатации.

Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды