Partlow MRC 7800 Скачать руководство пользователя страница 23

Страница: 23 / 57

AGE

4.5.3.2 MOVEMENT IN THE PROGRAM MODE

Each time the DOWN key is depressed while a parameter code is being displayed, such as

inPS

, another parameter code will be displayed.

Depressing the SCROLL key while a parameter code is displayed will cause the parameter

value to appear. Depressing the SCROLL key with a parameter value displayed will cause

the next parameter code to appear.

Depressing the UP key while a parameter code is being displayed will exit the Program mode

and

Prog

will appear in the display. Use the DOWN key to re-enter the mode, or the

SCROLL key to proceed to another mode.

4.5.3.3 ONE PEN INSTRUMENTS

For instruments specified and provided with only one pen, all configuration and operating

parameters and values will appear in the upper display, which is dedicated to Pen 1 and Unit

parameters. This is the only display provided.

PEn2

will not appear.

4.5.3.4 TWO PEN INSTRUMENTS

Instruments specified and provided with two pens require configuration of each pen.

4.5.3.5 PROGRAM MODE CONFIGURATION

Refer to Table 4-2 (page 26) for configuration procedures for the Program mode. All possible

parameters are shown for illustration purposes. Only those parameters applicable to each

respective pen and the unit will actually be shown.

4.5.4 ALARM SET MODE CONFIGURATION PROCEDURE

The Alarm Set mode allows the entry, review or altering of any of the alarm settings. Para-

meters to be configured will be only those that are applicable as determined by the hardware

provided or as assigned in the Program mode.

Review the entry procedure and the configuration procedures in Table 4-3 (page 30). Use

the "Your Setting" column in the table to record your programming.

4.5.4.1 ENTERING THE ALARM SET MODE

From the Operation or any other mode code, depress the SCROLL key until

ASEt

is dis-

played. With

ASEt

in the top display depress the DOWN key to enter the mode. If

ASEt

does not appear, then the mode has been disabled. Refer to Table 4-1 (page 25) for Enable

mode instructions.

4.5.4.2 MOVEMENT IN THE ALARM SET MODE

Each time the DOWN key is depressed while a parameter code is being displayed another

parameter code will be displayed.

Depressing the SCROLL key while a parameter code is displayed will cause the parameter

value to appear. Depressing the SCROLL key with a parameter value displayed will cause

the next parameter code to come up in the display.

Depressing the UP key while a parameter code is being displayed will exit the Alarm Set

mode and

ASEt

will appear in the display. Using the SCROLL key at this point will allow you

to proceed to any other mode.

4.5.4.3 ALARM SET MODE CONFIGURATION

Refer to Table 4-3 (page 30) for configuration procedures for the Alarm Set mode. All

possible parameters are shown for illustration purposes. Only those parameters applicable to

each respective pen will actually be shown.

Содержание MRC 7800


























































Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды

Partlow MRC 7800, Инструкция по установке, монтажу и эксплуатации.

Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды