Partlow MRC 7800 Скачать руководство пользователя страница 25

Страница: 25 / 57

AGE

4.5.7 TOTALIZATION CONFIGURATION

Selection of the totalization funciton, how to reset the totalizer, the decimal position, the low

flow cutoff point, the time base and the functions of the presets are all covered in the Program

mode. Preset values are adjusted in the Preset Adjust mode.

4.5.8 RESETTING THE TOTALIZER

Resetting the Totalizer (to 0) can be accomplished from the keypad or from a remote contact

closure.

Resetting the totalizer from the keypad for Pen 1 is accomplished by selecting the totalizer

display and by depressing the UP key and then also depressing the DISPLAY SELECT key

for 5 seconds. Resetting Pen 2 is accomplished by selecting the totalizer display and by

depressing the DOWN key and then also depressing the DISPLAY SELECT key for 5

seconds.

When the totalizer for Pen 1 is reset, the combined total is also reset.

Note: Remote Resetting of the totalizer will not operate if the unit is in the Off mode.

TABLE 4-1 ENABLE MODE

Press the UP and DOWN keys while in

oPEr

oFF

modes. All display lamps will light. After

10 seconds, the lamps will go out and

EnAb

will be displayed. Release the keys and the

display will change to

EtSt

. Press and release the DOWN key and each mode to be enabled/

disabled will be displayed. With the Enable mode prompt for the desired mode displayed,

press the SCROLL key to verify that the displayed mode is either

(enabled) or

oFF

(disabled). Press the DOWN key to turn off the mode, press the UP key to turn on the mode

or press the SCROLL key to advance the display to the next Enable mode prompt. Use the

"Your Setting" column in the table to record your programming. The Test and Calibration

modes are factory set to

oFF

(disabled).

DISPLAY

AVAILABLE

FACTORY

YOUR

STEP

DESCRIPTION

CODE

SETTINGS

SETTING

Enable Test Mode

EtSt

on or oFF

oFF

Enable Calibration Mode

ECAL

on or oFF

oFF

Enable Program Mode

EPro

on or oFF

Enable Alarm Set Mode

EASt

on or oFF

Enable Data Logger Setup

EdLS

on or oFF

Enable Data Logger Display

EdLd

on or oFF

Enable Preset Adjust Mode

EPSA

on or oFF

Содержание MRC 7800


























































Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды

Partlow MRC 7800, Инструкция по установке, монтажу и эксплуатации.

Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды