Partlow MRC 7800 Скачать руководство пользователя страница 50

Страница: 50 / 57

AGE

Appendix B
Glossary

Display Filter Factor

This parameter is adjustable from 1 to 20 which represents the number of scans of the

process variable that are averaged together before updating the displayed and recorded

value, and process value for retransmission. The factory default is 1=no filtering. Display

code

dFF

Flow Time Base

Specifies whether the displayed process value is in units/second, units/minute, units/hour or

units/day, such that the flow rate can be converted to flow for totalization. Factory default = 1,

units/second. Display code

Ftb

Hysteresis

The paramter is adjustable from 0 to 1000 units representing the width of the band (half above

and half below alarm setting). Factory default =10. Display code

HyAo

Input Correction

This parameter is adjustable from -1000 to 1000 units and is used as a method to compen-

sate for a linear sensor error. Factory default is 0=no correction. Display code

iCor

Platen

The flat surface in the instrument upon which the chart rotates.

Process Filter Factor

This parameter is adjustable from 1 to 20 which represents the number of scans per second

of the process variable that are averaged together before updating the process value used for

alarm, presets. The factory default value is 1=no filtering. Display code

PFF

Process Output

Allows retransmisstion of the process variable. Factory default is 0=not selected. Display

code

Pout

. If selected, a current output must be assigned to it and scaled using Process

Output upper and lower values.

Process Output Upper and Lower Values
(used in conjunction with process output)

These parameters specify the process value range over which the assigned current output will

decrease linearly from 100% to 0%. If the process value is greater than

Pou

the output will

be 100%. If the process value is less than

PoL

the output will be 0%. Factory default values

are 100.0 for the upper value and 0 for the lower value. Display codes

Pou

(upper) and

PoL

(lower).

Process Rounding

This parameter is adjustable from 0 to 1000 units and is used to round the process value to

the nearest value specified. Intended for use where the engineering units span is large, to

reduce fluctuation. Factory default is 0=no rounding. Display code

Prnd

(e.g.Prnd=3,

Process Value=-6, -3, 0, 3, 6, 9 ...).

Содержание MRC 7800


























































Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды

Partlow MRC 7800, Инструкция по установке, монтажу и эксплуатации.

Результаты поиска

Содержание MRC 7800

Отзывы:

Похожие инструкции для MRC 7800

Бренды по названию

Популярные бренды