manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, Руководство пользователя

Серия продуктов Paradyne COMSPHERE 3800 предлагает более усовершенствованные и надежные коммуникационные решения. Вы можете бесплатно скачать руководства пользователя и версии программного обеспечения на сайте manualshive.com, чтобы ознакомиться с последними обновлениями и изменениями в продукте. Улучшите свой опыт использования с помощью наших руководств.

Поделиться
Скачать
background image

COMSPHERE 3800 Series Modems

9-28

September 1998

3810-A2-GB30-30

Leased Line

The Leased Line configuration options are used to

configure the modem for operation over leased lines.

The Leased Line configuration group only appears if

the modem is configured with the Sync Leased factory
preset template, or when the &L1, &L2, &L3, or &L4
command is issued.

Table 9-5 shows each Leased Line configuration option

as it appears on the LCD, with the Async Dial factory
default setting (the default value if the modem is just
being installed) shown following the colon (:) on the first
line and with all available selections listed on the second
line. Following this is a description of the configuration
option, a description of the available selections, and any
equivalent AT commands.

Table 9-5

(1 of 5)

Leased Line Configuration Options

Leased Mode: 4WLL-Orig
Nxt

4WLL-Orig

4WLL-Ans

2WLL-Orig

2WLL-Ans

Leased Mode. Sets the modem for either 2-wire or 4-wire operation in Answer mode (receiving a call) or 2-wire or 4-wire
operation in Originate (initiating a call) mode. The only options available for Model 3820 modems are 2WLLOrig and
2WLL-Ans.

NOTE:  For proper operation over leased lines, one modem must be set for Originate mode and the other set for Answer

mode.

For Sync Leased Answer Mode, 4-wire Answer is the factory default. (Two-wire Answer for the Model 3820.) 
For Sync Leased Originate Mode, 4-wire Originate is the factory default. (Two-wire Originate for the Model 3820.)

AT command for Disable is &L0. 
AT command for 2-wire Originate is &L1. 
AT command for 4-wire Originate is &L2. 
AT command for 2-wire Answer is &L3. 
AT command for 4-wire Answer is &L4.

LeasedLine Rate: 19200(V32t)
Nxt   19200(V32t)   16800(V32t)   14400(V32b)   12000(V32b) 9600(V32b)   7200(V32b)   4800(V32b)   2400(V22bis)
14400(V33)   12000(V33)   9600(V29)   7200(V29)   4800(V29)

Leased-Line Rate. Determines the modem’s data rate and modulation scheme for operation on leased lines.

19200(V.32t), 16800(V32t), 14400(V.32bis), 12000(V.32bis), 9600(V.32bis), 7200(V.32bis), 4800(V.32bis) – These
modulation schemes are available on 2-wire or 4-wire leased lines. If a fixed V.32bis rate is selected, the modem can still
be commanded to fall back by a remote modem.

NOTE:  The modem must be in Direct mode before the modulation scheme can be changed from V.32bis to another

leased-line modulation (V.33 or V.22bis). See Err Contrl Mode configuration option for more about Direct mode.
On leased lines, V.42 error control and Buffer mode are only supported by V.32bis. An error occurs if the modem
is not in Direct mode when the modulation is changed from V.32bis. In asynchronous mode using V.22bis, the
DTE rate must equal the leased-line rate.

2400(V.22bis) – This modulation scheme is available on 2-wire and 4-wire leased lines.

14400(V.33), 12000(V.33), 9600(V.29), 7200(V.29), 4800(V.29) – These modulation schemes are available only on 4-wire
leased lines when the V.29 or V.33 options are installed, and are not available for the Model 3820.

NOTE:  It is recommended that both modems use the same fixed data rate.

The factory default is 19200(V32t).

AT command is S-Register S44=n, where n is: 

0, 1 = 14,400 bps (V.32bis) 

12 = 12,000 bps (V.33) 

2 = 12,000 bps (V.32bis) 

13 = 9600 bps (V.29) 

3 = 9600 bps (V.32bis)  

14 = 7200 bps (V.29) 

4 = 7200 bps (V.32bis)

15 = 4800 bps (V.29) 

5 = 4800 bps (V.32bis) 

18 = 19,200 (V.32terbo; default)

6 = 2400 bps (V.22bis)

19 = 16,800 (V.32terbo)

11 = 14,400 bps (V.33)

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

Multitech MultiModem MTCBA?EV1?U1?N3 User Manual preview
MultiModem MTCBA?EV1?U1?N3
Бренд: Multitech Страницы: 24
Farallon Netopia 412 User Manual preview
Netopia 412
Бренд: Farallon Страницы: 162
Haier WM220 User Manual preview
WM220
Бренд: Haier Страницы: 24
Haier WM200 User Manual preview
WM200
Бренд: Haier Страницы: 23
Zte Mblaze Ultra Wi-Fi User Manual preview
Mblaze Ultra Wi-Fi
Бренд: Zte Страницы: 73
ActionTec GT724WGR Specifications preview
GT724WGR
Бренд: ActionTec Страницы: 4
ActionTec External 56K Call Waiting User Manual preview
External 56K Call Waiting
Бренд: ActionTec Страницы: 33
ActionTec GT701A User Manual preview
GT701A
Бренд: ActionTec Страницы: 119
RADEMACHER RolloHomeControl 8430-1 Brief Instructions For Commissioning preview
RolloHomeControl 8430-1
Бренд: RADEMACHER Страницы: 2
SimpleTech STI-FAX/28.8 User Manual preview
STI-FAX/28.8
Бренд: SimpleTech Страницы: 90
Flash TC4300 Quick Installation Manual preview
TC4300
Бренд: Flash Страницы: 2
3Com 005687-03 - Manual preview
005687-03 -
Бренд: 3Com Страницы: 137
3Com 3CP5610A - U.S. Robotics 56K V90 PCI Performance Pro Faxmodem Dos/NT/Linux User Manual preview
3CP5610A - U.S. Robotics 56K V90 PCI Performance Pro Faxmodem Dos/NT/Linux
Бренд: 3Com Страницы: 100
3Com 005683-00 - Manual preview
005683-00 -
Бренд: 3Com Страницы: 101
Raisecom RC801-60B-FV35 Series User Manual preview
RC801-60B-FV35 Series
Бренд: Raisecom Страницы: 30
Raisecom RC801-30B-FV35-M User Manual preview
RC801-30B-FV35-M
Бренд: Raisecom Страницы: 18
Hanna Instruments HI 504902 Instruction Manual preview
HI 504902
Бренд: Hanna Instruments Страницы: 2
Raisecom RC1104-FE-4 A User Manual preview
RC1104-FE-4 A
Бренд: Raisecom Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды