manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, Руководство пользователя

Серия продуктов Paradyne COMSPHERE 3800 предлагает более усовершенствованные и надежные коммуникационные решения. Вы можете бесплатно скачать руководства пользователя и версии программного обеспечения на сайте manualshive.com, чтобы ознакомиться с последними обновлениями и изменениями в продукте. Улучшите свой опыт использования с помощью наших руководств.

Поделиться
Скачать
background image

Configure Branch

9-41

3810-A2-GB30-30

September 1998

Misc

The Miscellaneous configuration options determine

specifics for various functions, including network
management parameters and remote modem access. 

Table 9-8 shows each Misc (Miscellaneous)

configuration option as it appears on the LCD, with the
Async Dial factory default setting (the default value if the
modem is just being installed) shown following the 
colon (:) on the first line and with all available selections
listed on the second line. Following this is a description of
the configuration option, a description of the available
selections, and any equivalent AT commands.

Table 9-8

(1 of 4)

Miscellaneous Configuration Options

StrapsWhenDisc: No_Change
Nxt

No_Change

Reload   RelodNoATChg

Straps When Disconnected. Determines whether or not configuration options in the Active (Saved) configuration area
are reloaded to Active (Operating) when a disconnect occurs. This is useful in modem pooling applications.

No Change – Configuration options do not change upon disconnect.

Reload – The Active (Operating) configuration area, which controls modem operation, is reloaded from the Active
(Saved) configuration area when a disconnect occurs. This is useful in modem pooling applications where it is desirable
to start the modem from a known condition after every call. This allows multiple users to issue AT commands to change
the modem’s operation for their particular call.

Reload, No AT Change – This has the same effect as Reload, except that it becomes impossible to change this
configuration option with an AT command, and the command buffer is cleared so that AT\A (Repeat Last Command) has
no effect.

NOTE:  If Reload or RelodNoATChg is selected, the following AT commands are disabled although the OK result code

appears when these commands are issued: 

AT&F0. Loads Async Dial into Active(Operating) 
AT&F1. Loads Sync Dial into Active (Operating) 
AT&F2. Loads Sync Leased (Answer) into Active (Operating) 
AT&F3. Loads UNIX Dial into Active(Operating) 
AT&F4. Loads Sync Leased (Originate) into Active (Operating) 
AT&F5. Loads Cellular(Mobile) into Active (Operating)
AT&F6. Loads Cellular (PSTN) into Active (Operating)
AT&W0. Write Active(Operating) to Active(Saved) 
AT&W1. Write Active(Operating) to Customer 1 
AT&W2. Write Active(Operating) to Customer 2 
AT&Zn=x. Store directory numbers

The factory default is No_Change.

AT command for No_Change is S88 = 0 or S88 = 231. 
AT command for Reload is S88 = 1 or S88 = 232. 
AT command for Reload with no AT Change is S88 = 2 or S88 = 233.

Speaker Control: OnUntilCarr
NxtOn

UntilCarr

Off

On

Speaker Control. Determines if the speaker is Off, On until carrier signal is received by the modem, or On all the time.

The factory default is OnUntilCarr.

NOTE:  Speaker Control can also be temporarily set using the Control branch; however, a reset or power cycle will

restore the modem to the Speaker Control and Speaker Volume configuration option settings.

AT command for Off is M0 AT command for On Until CD is M1. 
AT command for On is M2.

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

Kantronics TALON UDC SERIES Service Manual preview
TALON UDC SERIES
Бренд: Kantronics Страницы: 23
RACOM RipEX 1.4 User Manual preview
RipEX 1.4
Бренд: RACOM Страницы: 157
Multitech MultiModem MTCBA?EV1?U1?N3 User Manual preview
MultiModem MTCBA?EV1?U1?N3
Бренд: Multitech Страницы: 24
D-Link DIM-128 User Manual preview
DIM-128
Бренд: D-Link Страницы: 53
D-Link DCM-604 Series User Manual preview
DCM-604 Series
Бренд: D-Link Страницы: 32
D-Link DCM-3012G Quick Installation Manual preview
DCM-3012G
Бренд: D-Link Страницы: 5
D-Link DCM202 - Express Ethernetwork DOCSIS 2.0 Cable Modem Quick Installation Manual preview
DCM202 - Express Ethernetwork DOCSIS 2.0 Cable Modem
Бренд: D-Link Страницы: 36
D-Link DSL-100D User Manual preview
DSL-100D
Бренд: D-Link Страницы: 48
D-Link DP-601M User Manual preview
DP-601M
Бренд: D-Link Страницы: 95
D-Link DMW-221 User Manual preview
DMW-221
Бренд: D-Link Страницы: 9
Toshiba V.9256K User Manual preview
V.9256K
Бренд: Toshiba Страницы: 120
Globe Internet Unlimited Single User Wi-Max USB Modem User Manual preview
Unlimited Single User Wi-Max USB Modem
Бренд: Globe Internet Страницы: 5
Globe Tattoo User Manual preview
Tattoo
Бренд: Globe Страницы: 12
Radyne DMD2050 Operation Manual preview
DMD2050
Бренд: Radyne Страницы: 214
Abocom ISM56CR Quick Installation Manual preview
ISM56CR
Бренд: Abocom Страницы: 20
Patton electronics 1080A User Manual preview
1080A
Бренд: Patton electronics Страницы: 15
ADTRAN 1200861L1 Quick Start Manual preview
1200861L1
Бренд: ADTRAN Страницы: 2
ADTRAN 1203153L2 User Manual preview
1203153L2
Бренд: ADTRAN Страницы: 146

Бренды по названию

Популярные бренды

Загрузить еще бренды