Paradyne COMSPHERE 3800 Series Скачать руководство пользователя | Manualshive

Страница: 187 / 213

background image

COMSPHERE 3800 Series Modems

F-2

September 1998

3810-A2-GB30-30

, or <

User-Defined Pause

&

Flash Hook

= or >

Delimiters

Call Request with Stored
Memory Address Provided (CRS)

The CRS command dials the telephone number stored

in the request directory location. CRS is similar to the
ATDS command.

The CRS command format is:

CRSx

Where:

x is directory location 1–10.

The modem responds to the command with either a

VAL (valid) or INV (invalid) response followed by a call
progress report such as connect (CNX) or failure (CFI).

Call Response

A Call Response indicates if the command was

accepted by the modem. Call Response includes Call
Failure Indication (CFI) and Call Connecting (CNX).

Call Failure Indication (CFI)

The CFI response is issued to the DTE if the modem

fails a CRN or CRS command. CFI is similar to the AT
result codes BUSY, NO ANSWER, NO CARRIER, NO
DIALTONE, and ERROR.

The CFI response format is:

CFIxx

Where:

xx is

ET

Engaged tone

NS

Number not stored

CB

Local DCE busy

RT

Timeout on ring tone

AB

Abort call on time-out

NT

Answer tone not detected

FC Forbidden

call

ET is similar to the Call Failure Messages, Busy Signal

and Trunk Busy and the result code BUSY.

NS is similar to the Common Operational Message

Invalid Number and the result code ERROR.

CB is similar to the Call Failure Messages, Dial Line in

Use and No Dial-Test and the result code ERROR.

RT is similar to the Call Failure Message No Answer

Tone and the result code NO CARRIER.

AB is similar to the Call Failure Messages, No Dial

Tone and No Dial-DTR and the result code NO
DIALTONE and ERROR.

NT is similar to the Call Failure Message No Quiet

Answer and the result code NO ANSWER.

Call Connecting (CNX)

The CNX response informs the DTE that the modem

has connected to the remote modem. CNX is similar to the
AT result code CONNECT.

The CNX response format is CNX.

Call Answer Commands

Call Answer commands disable or enable the modem’s

AutoAnswer function. These commands are issued from
the DTE. Call Answer commands include Incoming Call
(INC), Disregard Incoming Call (DIC) and Connect
Incoming Call (CIC).

Incoming Call (INC)

The INC response informs the DTE that the modem

has detected a ring tone. At this point, the DTE can issue
the DIC command to disable the modem from answering
the call. INC is similar to the AT result code RING.

Disregard Incoming Call (DIC)

The DIC command prevents the modem from

answering an incoming call. This command is only valid
once the DTE receives an incoming call (INC) response
from the modem. A DIC must be issued within
5 seconds after receiving an INC.

The DIC command format is DIC.

If DIC is issued within 5 seconds, the modem sends the

VAL response to the DTE. If DIC is issued after 5
seconds, INV is returned.

«
...
185
186
187
188
189
...
»

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

ComStream DMD2401

Бренд: Radyne Страницы: 199

MultiModem CMDA MTCBA-C1X

Бренд: Multitech Страницы: 17

Бренд: Real Time Devices Страницы: 33

Бренд: Paradyne Страницы: 60

Бренд: Farallon Страницы: 162

Бренд: Huawei Страницы: 59

Бренд: Huawei Страницы: 10

Бренд: Huawei Страницы: 16

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 3

Бренд: Huawei Страницы: 20

Бренд: Huawei Страницы: 5

Бренд: Huawei Страницы: 21

Бренд: Huawei Страницы: 22

Бренд: Huawei Страницы: 22

Бренд: Huawei Страницы: 3

Бренд: Huawei Страницы: 32

Бренд: Huawei Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды