Paradyne COMSPHERE 3800 Series Скачать руководство пользователя | Manualshive

Страница: 89 / 213

background image

COMSPHERE 3800 Series Modems

9-20

September 1998

3810-A2-GB30-30

Line Dialer

The Line Dialer configuration options establish

parameters used by the modem to answer or originate
calls.

Table 9-3 shows each Line Dialer configuration option

as it appears on the LCD, with the Async Dial factory
default setting (the default value if the modem is just
being installed) shown following the colon (:) on the first
line and with all available selections listed on the second
line. Following this is a description of the configuration
option, a description of the available selections, and any
equivalent AT commands.

Table 9-3

(1 of 5)

Line Dialer Configuration Options

AutoAnswerRing#: 1
Nxt

1

Disable

2

4

6

8

10

Auto-Answer Ring Count. Determines the number of rings necessary before the answering modem answers an incoming
call. For example, if this option is set for 2, then the answering modem answers after the second ring.

NOTE: Although DCP selections are limited (1, 2, 4, 6, 8, or 10), values set by AT commands can display from 1 to

255 rings.

Disable – If selected, the modem must be answered using either the DCP’s Answer command or Tlk/Data function or
via AT commands.

The factory default is 1.

AT command to disable is S0 = 0.
AT command is S-register S0 = n, where n is a ring count from 1 to 255.

Dialer Type: Tone
Nxt

Tone

Pulse

Dialer Type. Selects either tone (DTMF) dialing or pulse (rotary) dialing mode.

The factory default is Tone.

AT command for tone dialing is T.
AT command for pulse dialing is P.

DialTone Detect: Enable
Nxt

Enable

Disable

Dial Tone Detect. Sets the modem for dial tone detection (enable) or blind dialing (disable).

Enable – Modem disconnects the call if a dial tone is not detected within 10 seconds and displays No Dial Tone on both
the LCD and asynchronous DTE terminal.

Disable – Modem dials a call whether or not it detects a dial tone on the line. This is known as blind dialing. The period
of time the modem waits before dialing is specified in the Blind Dial Pause configuration option.

The factory default is Enable.

AT commands to disable are X0, X1, and X3.
AT commands to enable are X2, X4, X5, X6, and X7.

«
...
87
88
89
90
91
...
»

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

Бренд: Skypatrol Страницы: 33

Бренд: NCXX Страницы: 12

Photo Backup Stick Universal

Бренд: Paraben Страницы: 10

Бренд: Abocom Страницы: 1

Бренд: Vahle Страницы: 16

PlantLinc PLR5000

Бренд: Data-Linc Group Страницы: 31

Бренд: Toshiba Страницы: 18

PCX1100 - DOCSIS Cable Modem

Бренд: Toshiba Страницы: 21

Бренд: Toshiba Страницы: 22

Бренд: Toshiba Страницы: 22

Бренд: Toshiba Страницы: 22

DOCSIS DAZ8820F

Бренд: Toshiba Страницы: 22

Бренд: Toshiba Страницы: 53

Бренд: Realme Страницы: 24

Бренд: Zhone Страницы: 5

Бренд: TAPR Страницы: 12

COMSPHERE 3810Plus

Бренд: Paradyne Страницы: 28

Бренд: IFM Electronic Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды