Paradyne COMSPHERE 3800 Series Скачать руководство пользователя | Manualshive

Страница: 106 / 213

background image

Configure Branch

9-37

3810-A2-GB30-30

September 1998

Table 9-6

(5 of 6)

V.42/MNP/Buffer Configuration Options

*Break Buffr Ctl: Keep_Data

Nxt

Keep_Data

Discard_Data

Break Buffer Control. Determines if data stored in the modem’s buffer is saved or discarded when the DTE issues a
break sequence.

Keep Data (Nondestructive mode) – Saves the data in the buffer in both the local and remote modems.

Discard Data (Destructive mode) – Empties the data buffer. Only buffers in the same direction of travel as the break
are discarded.

The factory default is Keep Data.

NOTE: This configuration option is ignored if the Break Forces Escape configuration option (see DTE Dialer

configuration options group) is enabled.

AT commands for Discard Data are \K0 and \K1.
AT commands for Keep Data are \K2, \K3, \K4, and \K5.

*Send Break Cntl: Data_First

Nxt

Data_First

Break_First

Send Break Control. Determines what is sent from the modem first, data or break if a break sequence is sent from the
DTE.

Data First (Nonexpedited) – A break is treated as a data character and is sent in the order it was received. This is also
known as Nonexpedited mode.

Break First (Expedited) – A break is sent before the data currently in the buffer. This is also known as Expedited mode.

The factory default is Data First.

NOTE: This configuration option is ignored if the Break Forces Escape configuration option (see DTE Dialer

configuration options group) is enabled.

AT commands for Break First are \K0, \K1, \K2, and \K3. AT commands for Data First are \K4 and \K5.

*TXBuffDiscDelay: 10sec

Nxt

10sec

60sec

Disable

The Transmit Buffer Disconnect Delay is the maximum amount of time the modem can continue to send data in its
Transmit Buffer to the remote modem after it is commanded by the DTE to disconnect. Disable means that the
disconnect occurs immediately. The default is 10 seconds.

Disable – Modem disconnects immediately without attempting to send data stored in its buffers.

10, 60 sec – Maximum amount of time the modem tries to empty its buffers before disconnecting. In both cases (10 sec
and 60 sec), the modem disconnects much sooner if it can empty its buffers.

NOTE: This configuration option is not available if Error Control Mode configuration option is set for DirectMode.

AT command is S-register S49 = n, where n is 0 for Disable and any value from 1 to 255 in 1 second increments.

* This configuration option is only available if Async/Sync Mode is configured for Async. Refer to the DTE Interface

configuration options group for more on Async/Sync Mode.

«
...
104
105
106
107
108
...
»

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

Бренд: Comtrend Corporation Страницы: 10

Бренд: Osaka Страницы: 50

Vigor120 Series

Бренд: Draytek Страницы: 8

T2-B-Gawv1.4U10Y-BI

Бренд: Teracom Страницы: 131

PlantLinc PLR5000

Бренд: Data-Linc Group Страницы: 31

Бренд: Dynex Страницы: 8

Бренд: Blue Tree Страницы: 2

Бренд: Sandberg Страницы: 32

Бренд: TP-Link Страницы: 2

Ins-60007-gd-us

Бренд: Paxton Страницы: 8

Бренд: Franklin Wireless Страницы: 24

Бренд: AvL Technologies Страницы: 12

Бренд: Fargo Страницы: 11

Бренд: Motorola Страницы: 24

Бренд: Dataradio Страницы: 26

Бренд: Raveon Страницы: 51

Бренд: Bascom Страницы: 36

RocketLink-G 3088 Series

Бренд: Patton electronics Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды