manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, Руководство пользователя

Серия продуктов Paradyne COMSPHERE 3800 предлагает более усовершенствованные и надежные коммуникационные решения. Вы можете бесплатно скачать руководства пользователя и версии программного обеспечения на сайте manualshive.com, чтобы ознакомиться с последними обновлениями и изменениями в продукте. Улучшите свой опыт использования с помощью наших руководств.

Поделиться
Скачать
background image

COMSPHERE 3800 Series Modems

9-32

September 1998

3810-A2-GB30-30

Table 9-5

(5 of 5)

Leased Line Configuration Options

AutoDialStandby: Disable
Nxt

Disable

15min   30min   1hr

4hr   Test(2min)   Adv15min

Adv30min   Adv1hr

TestAdv2min

Automatic Dial Standby. Permits a modem operating on dial lines (regardless of the method of dialing origination) to
check the quality of the leased lines periodically and, if they are good, to disconnect from the dial lines and resume
operations on the leased lines. This configuration option is not available on the Model 3820.

The time interval that the modem uses to check the quality of the leased lines is determined by the configuration option.
These intervals are 15 minutes, 30 minutes, 1 hour, and 4 hours.

The normal settings cause a lapse of data flow on the dial line while the leased-line connection is checked. The
Advanced settings allow data flow to continue without interruption while the leased line is evaluated. If Advanced
settings are used, then both modems must be configured to the same Advanced setting.

The Test(2min) and TestAdv2min selections are for testing this feature only.

The factory default is Disable.

AT command is S-register S47 = n :

S47 = 0

Disable

S47 = 1

15min

S47 = 2

1hr

S47 = 3

4hrs

S47 = 4

Test(2min)

S47 = 5

Advanced 15min

S47 = 6

Advanced 1hr

S47 = 7

Advanced 4hrs

S47 = 8

Advanced Test(2min)

CarrierOn Level: – 43dbm
Nxt – 43dbm – 26dbm

Carrier On Level. This configuration option controls the carrier detection threshold for leased lines. When the power level
of the receive carrier signal drops 2 dBm below this level (either – 26 dBm or – 43 dBm), LSD turns Off. When the carrier
signal is greater than this level, LSD turns ON.

The factory default is – 43dbm.

AT command is S-register S48 = n, where n is 0 for – 43 dBm or 1 for – 26 dBm.

V29 TrainOnData: Disable
Nxt   Disable   Enable

V.29 Train On Data. Appears only if the V.29 Option is installed, and effective only if V.29 is selected for the leased-line
rate. Determines whether the modem must receive a standard V.29 training sequence in order to enter Data mode
(Disable) or whether it should use the received Data mode for training (Enable).

The factory default is Disable.

AT command is S-register S92 = n, where n is 0 for Disable or 1 for Enable.

FallFwdDelay: Disable
End   Disable   5_mins   15_mins   1_hour

Fall Forward Delay. Provides an initial delay before leased or dial lines are monitored for fall forward conditions. After the
timer expires, monitoring occurs as usual. Possible delay times are 5 minutes, 15 minutes, or 1 hour.

The factory default is Disable (no delay).

NOTE:  Fall Forward Delay appears under both the Dial Line configuration options and the Leased Line configuration

options, but the same setting is used for both. Changing it in one place effectively changes it in the other.

There is no analogous AT command, so this configuration option is not available for modems without a shared or integral
DCP.

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

Multitech MultiConnect Cell MTC-LVW2 User Manual preview
MultiConnect Cell MTC-LVW2
Бренд: Multitech Страницы: 41
Virgin Home Modem User Manual preview
Home Modem
Бренд: Virgin Страницы: 44
Kcell CONNECT MF656A Quick User Manual preview
CONNECT MF656A
Бренд: Kcell Страницы: 20
Novatel Ovation MC998D Product User Manual preview
Ovation MC998D
Бренд: Novatel Страницы: 28
Sixnet VT-MODEM User Manual preview
VT-MODEM
Бренд: Sixnet Страницы: 30
Cygnus 850 Quick Start Installation Manual preview
850
Бренд: Cygnus Страницы: 6
Belkin F1PI242ENAU Quick Installation Manual preview
F1PI242ENAU
Бренд: Belkin Страницы: 4
Huawei Mobile Internet Key Quick Start Manual preview
Mobile Internet Key
Бренд: Huawei Страницы: 12
IOM Holdings HI-VAL 56K User Manual preview
HI-VAL 56K
Бренд: IOM Holdings Страницы: 31
Ebyte E890-868LG12 User Manual preview
E890-868LG12
Бренд: Ebyte Страницы: 31
Fritz! FRITZ!Box 6660 Cable Configuration And Operation preview
FRITZ!Box 6660 Cable
Бренд: Fritz! Страницы: 281
Camatel NetVito 5300 Series Quick Start Manual preview
NetVito 5300 Series
Бренд: Camatel Страницы: 12
A1 WLAN Box Quick Start Manual preview
WLAN Box
Бренд: A1 Страницы: 2
Hama 00053309 Manual preview
00053309
Бренд: Hama Страницы: 2
TATA Motors Photon Whiz User Manual preview
Photon Whiz
Бренд: TATA Motors Страницы: 48
DAVIS SPREAD-SPECTRUM RADIO MODEM Manual preview
SPREAD-SPECTRUM RADIO MODEM
Бренд: DAVIS Страницы: 36
ESTeem 195Es Quick Start Manual preview
195Es
Бренд: ESTeem Страницы: 12
Omega OMEGABUS A2400 User Manual preview
OMEGABUS A2400
Бренд: Omega Страницы: 68

Бренды по названию

Популярные бренды

Загрузить еще бренды