Paradyne COMSPHERE 3800 Series Скачать руководство пользователя | Manualshive

Страница: 120 / 213

background image

Control Branch

10-5

3810-A2-GB30-30

September 1998

At this point, if you do not want to continue this

process, abort the transfer by selecting any function key.
This returns the modem to the Top-Level menu.

However, to continue with the transfer, press the

key to display the Reprogram_Remote selection.

F1

Warning : Download
Reprogram_Remote

F2

F3

Press any function key to begin the transfer.

F1

RemClone Status
Establish Remote

F2

F3

The local modem’s LCD displays Establish Remote,

indicating the modem is attempting to establish a Remote
Cloning Download session with the remote modem.

If unsuccessful, the modem remains in the Download

Transfer mode. The LCD’s top line displays RemClone
Failed and the bottom line displays one of the following
messages:

Incompat
Modulat

The modems are connected,
but are using a modulation
scheme other than V.33,
V.32bis, V.32, or V.29.

No Response

The remote modem is not a
3800 Series modem or the
connection between the two
modems is poor.

Access
Disabled

The remote modem’s Access
from Remote configuration is
disabled. Also is displayed if
the local modem has a
firmware release prior to
Release 3.0 and the remote
modem has Release 3.0 or
greater installed with either
Answer Access Security or
Originate Access Security
enabled. In this case, both
security methods must be
disabled in the remote modem
to achieve the download.

Password
Invalid

The local and remote
modems’ passwords do not
match.

Correct the problem and attempt another download

from the local modem. If this fails, contact your service
representative.

After successful establishment of a Remote Cloning

Download session, the following screens are displayed.

F1

RemClone Status
Initializing

F2

F3

F1

RemClone Status
Bank 1 : xxxx/yyyy

F2

F3

«
...
118
119
120
121
122
...
»

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

Бренд: iRZ Страницы: 20

Бренд: Comtrend Corporation Страницы: 10

Бренд: NetComm Страницы: 92

Бренд: LG Innotek Страницы: 27

Бренд: Zte Страницы: 25

Бренд: Zte Страницы: 36

Бренд: PPL Страницы: 2

Бренд: MOVITEL Страницы: 28

Бренд: Zte Страницы: 27

Бренд: Zoom Страницы: 61

Бренд: Dynex Страницы: 16

Бренд: Ebyte Страницы: 17

Бренд: Tait Страницы: 30

Бренд: Paradyne Страницы: 125

Бренд: Westermo Страницы: 24

Бренд: Hughes Network Страницы: 122

Бренд: SMC Networks Страницы: 138

TJ 700x Series DOCSIS

Бренд: Terayon Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды