Paradyne COMSPHERE 3800 Series Скачать руководство пользователя | Manualshive

Страница: 41 / 213

background image

COMSPHERE 3800 Series Modems

4-10

September 1998

3810-A2-GB30-30

Table 4-4

(3 of 3)

Top-Level Menu Status

Dial Backup

Messages

Indicates

Dial Standby

The modem is operating in Dial Standby mode.

DialBckUp:MR*

The modem is operating in a Dial Backup mode at the displayed data rate and is configured for
Direct mode.

Backup:MR* EC**

The modem is operating in Dial Backup mode and is configured for error control and data
compression on leased lines.

Stndby:MR* EC**

The modem is operating in Dial Standby mode and is configured for error control and data
compression on leased lines.

Firmware

Download Result

Messages

Indicates

DownldOnly Mode

Indicates that a local download of firmware or a remote cloning of firmware has failed. The
modem is currently in a Download Only mode in which only another download attempt is possible.

Frmware Upgrade

Indicates that a local download of firmware or a remote cloning of firmware was successful.

RemClone Failed

Displays on the local modem’s LCD and indicates that a remote cloning of firmware has failed.

Remote Clone OK

Displays on the local modem’s LCD and indicates that a remote cloning of firmware was
successful.

AT Command

Reset Message

Indicates

Reset by AT
command

The modem has performed a reset in response to an ATZ command.

* MR. Modem Rate indicates the data rate the modem is using. One of the following values appears: 300, 1200, 2400,

4800, 7200, 9600, 12K (12,000), 14.4 (14,400), 16.8 (16,800), or 19.2 (19,200) bps.

** EC. Error Control indicates the modem is online and using V.42 or MNP error control. One of the following values

appears after the modem rates listed above: MNP2, MNP3, MNP4, MNP5, V42, V42b, or NoEC. (NoEC indicates the
modem is connected in Buffer mode rather than error control. If an EC value does not appear, then the modem is in
Direct mode.)

«
...
39
40
41
42
43
...
»

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

WEBR@CER 852 PSTN

Бренд: Topcom Страницы: 38

Бренд: XtendLan Страницы: 95

Бренд: Dynamix Страницы: 2

Бренд: Huawei Страницы: 17

Бренд: Huawei Страницы: 20

Бренд: Huawei Страницы: 21

Бренд: Huawei Страницы: 23

Бренд: Huawei Страницы: 21

Бренд: Huawei Страницы: 10

Бренд: 3Com Страницы: 56

Бренд: 3Com Страницы: 66

Бренд: RCA Страницы: 9

Бренд: ADB Страницы: 104

Бренд: Zte Страницы: 7

Бренд: dji Страницы: 71

Бренд: ICP DAS USA Страницы: 39

Бренд: Ebyte Страницы: 25

Бренд: Ebyte Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды