manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, Руководство пользователя

Серия продуктов Paradyne COMSPHERE 3800 предлагает более усовершенствованные и надежные коммуникационные решения. Вы можете бесплатно скачать руководства пользователя и версии программного обеспечения на сайте manualshive.com, чтобы ознакомиться с последними обновлениями и изменениями в продукте. Улучшите свой опыт использования с помощью наших руководств.

Поделиться
Скачать
background image

Configure Branch

9-33

3810-A2-GB30-30

September 1998

V.42/MNP/Buffer

V.42/MNP/Buffer configuration options determine the

type of error correction and flow control used by the
modems and attached DTEs.

Some choices within this group may not appear

depending upon how previous configuration options have
been selected. If the Async/Sync Mode configuration
option is set for synchronous operation (see DTE Interface
configuration options group), then the V.42/MNP/Buffer
group does not appear on the LCD. Any changes made to
configuration options within this group only take effect
after a disconnect.

Table 9-6 shows each V.42/MNP/Buffer configuration

option as it appears on the LCD, with the Async Dial
factory default setting (the default value if the modem is
just being installed) shown following the colon (:) on the
first line and with all available selections listed on the
second line. Following this is a description of the
configuration option, a description of the available
selections, and any equivalent AT commands.

Table 9-6

(1 of 6)

V.42/MNP/Buffer Configuration Options

*Err Contrl Mode: V42/MNPorBfr

Nxt

V42/MNPorBfr

V42/MNPorDsc

MNP_or_Buffr

MNP_or_Disc   Buffer Mode   DirectMode

LAPM_or_Disc   LAPM_or_Buffr

Determines the type of error control used by the modem. In most cases, V42/MNPorBfr is the best choice. If V.42bis and
MNP are enabled, then the modem uses the following priority for error control negotiation: V.42bis, V.42, MNP 5 and
below. Online changes do not take effect until a disconnect occurs.

V.42/MNP or Buffer – Modem attempts to connect in V.42 Error Control mode. If this fails, the modem attempts to
connect in MNP mode. If this fails, the modem connects in Buffer mode and continues operation. This is also known as
V42/MNP Autoreliable Mode.

V.42/MNP or Disconnect – Modem attempts to connect in V.42 Error Control mode. If this fails, the modem attempts to
connect in MNP mode. If this fails, the modem disconnects. This is also known as Reliable mode.

MNP or Buffer – Modem attempts to connect in MNP mode. If this fails, the modem connects in Buffer mode. This is
also known as MNP Autoreliable Mode.

MNP or Disconnect – Modem attempts to connect in MNP mode. If this fails, the modem disconnects. This is also
known as Reliable mode.

Buffer Mode – Modem does not use error control and allows the DTE rate to differ from the communications line rate.
This mode should only be used if the DTE provides its own error control or if errors in data can be tolerated. This setting
is also known as Normal mode and is valid even if the remote modem is set for Direct mode.

Direct Mode – Modem connects at a data rate equal to or less than the initial DTE interface rate. (The modem never
connects at a data rate greater than the initial DTE rate.) If the modem connects at a data rate lower than the DTE rate,
the DTE must then adjust its data rate to equal the modem rate. Ultimately, the modem speed and DTE speed must be
the same. Direct mode does not support error control or data buffering.

LAPM or Disconnect – Modem attempts to connect in V.42 Link Access Procedure for Modems (LAPM) error control
mode. If this fails, the modem attempts to connect in MNP mode. If this fails, the modem disconnects. This setting
should be used for cellular connections (at both the mobile and PSTN sides) when it is known that both sides support
V.42.

LAPM or Buffer – Modem attempts to connect in V.42 LAPM error control mode. If this fails, the modem attempts to
connect in MNP mode. If this fails, the modem connects in Buffer mode and continues operation.

NOTE:  The modem must be reconfigured for Direct mode before changing the leased-line modulation if V.42 error

control or Buffer mode are enabled with V.32bis on leased lines.

* This configuration option is only available if Async/Sync Mode is configured for Async. Refer to the DTE Interface 

configuration options group for more on Async/Sync Mode.

Содержание COMSPHERE 3800 Series






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3800 Series

Wavecom SAM User Manual preview
SAM
Бренд: Wavecom Страницы: 18
SCS PTC-IIIusb User Manual preview
PTC-IIIusb
Бренд: SCS Страницы: 217
ADC MM300S Installation Manual preview
MM300S
Бренд: ADC Страницы: 7
i-mate JASJAR Manuallines For Use preview
JASJAR
Бренд: i-mate Страницы: 7
OUMAN GSMMOD12 Quick Start Manual preview
GSMMOD12
Бренд: OUMAN Страницы: 8
CAME 806SA-0140 Manual preview
806SA-0140
Бренд: CAME Страницы: 24
ZyXEL Communications P841C User Manual preview
P841C
Бренд: ZyXEL Communications Страницы: 41
Haier WM220 User Manual preview
WM220
Бренд: Haier Страницы: 24
Haier WM200 User Manual preview
WM200
Бренд: Haier Страницы: 23
Motorola Premium Motorola 3347 Quick Manual preview
Premium Motorola 3347
Бренд: Motorola Страницы: 11
Motorola ML1500 Quick Start Manual preview
ML1500
Бренд: Motorola Страницы: 16
Motorola SURFboard SB5102 User Manual preview
SURFboard SB5102
Бренд: Motorola Страницы: 47
Motorola SURFboard SB4220 Series User Manual preview
SURFboard SB4220 Series
Бренд: Motorola Страницы: 66
Motorola SURFboard SB5102 Quick Installation Manual preview
SURFboard SB5102
Бренд: Motorola Страницы: 2
Motorola SURFboard SBV5122 Installation Manual preview
SURFboard SBV5122
Бренд: Motorola Страницы: 24
Motorola SURFboard SB6121 Installation Manual preview
SURFboard SB6121
Бренд: Motorola Страницы: 27
Motorola PRM240 i User Manual preview
PRM240 i
Бренд: Motorola Страницы: 36
Motorola SBV5322 SURFBOARD DIGITAL VOICE MODEM - annexe 3 (Spanish) Guía Del Usuario preview
SBV5322 SURFBOARD DIGITAL VOICE MODEM - annexe 3
Бренд: Motorola Страницы: 43

Бренды по названию

Популярные бренды

Загрузить еще бренды