Paradyne 9121 Скачать руководство пользователя страница 53

Страница: 53 / 73

Maintenance and Troubleshooting

5-3

9121-A2-GB20-00

June 1997

Label

What It Means

Color

Indication

TST

Test Mode

Yellow

ON –

Loopback or test pattern in progress,
initiated locally, remotely, or from the
network.

OFF –

No tests are active.

BKP

Backup

Yellow

ON –

Access unit is in Backup mode;
that is, the backup link has been
established, and backup is in progress
through the specified Alternate
Destination Link.

OFF –

Access unit is not in Backup mode;
that is, unit is idle, or is originating or
answering a backup call.

Blinking ON and OFF ( Rate: 1 Hz ) –

Alternate Destination Link is being
established, but no data has been
passed.

Network/DSX Interface

Label

Indication

Color

What It Means

SIG

Signal

Green

– A recoverable signal is present on the

Network/DSX interface.

OFF – The signal cannot be recovered from

the Network/DSX interface. An LOS
condition exists.

OOF

Out of Frame

Yellow

– At least one OOF was detected during

the sampling period.

OFF – No OOFs were detected during the

sampling period.

ALM

Alarm

Yellow

– An alarm condition is present on the

network/DSX interface.

Current alarm conditions:

Loss of Signal ( LOS )

Out of Frame (OOF)

Excessive Error Rate (EER)

Yellow

Alarm Indication Signal (AIS)

OFF – No alarm condition is present on the

Network/DSX interface.

Содержание 9121









































































Результаты поиска

Содержание 9121

Отзывы:

Paradyne 9121, Руководство пользователя, Страница: 53 / 73

Результаты поиска

Содержание 9121

Отзывы: