Paradyne 9121 Скачать руководство пользователя страница 28

Страница: 28 / 73

Displaying System Information

4-4

9121-A2-GB20-00

June 1997

Health and Status Messages:

These messages appear in the left-most column of the System and Test Status
screen, or the highest priority Health and Status message appears on the last line
at the bottom of the screen (right-most corner).

Message

What It Indicates

What To Do

AIS at Network

An Alarm Indication Signal
(AIS) is received by the
network interface. AIS is an
unframed, all ones signal.

1. Upstream access unit is

transmitting AIS
(keep-alive signal).

2. The network is

transmitting an AIS.

1. Check status of upstream

access unit(s).

2. Report problem to carrier.

AIS at DSX-1

An Alarm Indication Signal
(AIS) is received by the
DSX-1 interface. AIS is an
unframed, all ones signal.

Check the DTE attached to the
DSX-1 interface.

Backup Active

Backup has been
established and data is
flowing over the alternate
DLCI.

No action needed.

BRI-B

n Call Profile

Disabled

ISDN backup call (manual
or automatic) could not be
made because the Call
Profile had been disabled.

Enable the ISDN Call Profile
(

Main Menu

→

Control

→

ISDN Call Profiles

→

Enable)

BRI-B

n Call Profile

Invalid

ISDN backup call (manual
or automatic) could not be
made because the Call
Profile is invalid.

1. Verify that the ISDN Call

Profile identifier is not blank.

2. Check that the phone number

associated with the ISDN Call
Profile is valid.

BRI-B

n Call

Terminated by
Remote End

ISDN backup call (manual
or automatic) was not
successful because it was
terminated at the remote
end.

1. Check configuration of the

remote device.

2. Verify that the remote device

is configured answer calls.

3. Verify Calling IDs.

Configuration Shortcut
Active

Configuration Shortcuts
feature is active, which
allows automatic
configuration and
cross-connection of DLCIs
as they are activated by the
network.

No action needed unless you
want to disable this feature,
selected from the Main Menu.

CTS down to Port -

Device

The Port

n CTS control

lead on the access unit is
off.

1. Verify that the port is enabled.

2. Check DTR from Port-1 or

Port-2.

Содержание 9121









































































Результаты поиска

Содержание 9121

Отзывы:

Paradyne 9121, Руководство пользователя, Страница: 28 / 73

Результаты поиска

Содержание 9121

Отзывы: