Paradyne 9121 Скачать руководство пользователя страница 34

Страница: 34 / 73

Displaying System Information

4-10

9121-A2-GB20-00

June 1997

Message

What To Do

What It Indicates

NAM Fail

One or more of the NAM’s
integrated circuit chips
failed internal device level
testing.

1. Reset the unit and try again.

2. Call your service

representative for assistance.

3. Return the unit to the factory

(see

Page A

at the front of this

guide).

Network T1 Fail

The NAM failed to internally
loop data on the network
T1 circuit.

1. Reset the unit and try again.

2. Call your service

representative for assistance.

3. Return the unit to the factory

(see

Page A

at the front of this

guide).

Passed

Self-Test is enabled, the
access unit has been
plugged in (or reset ), the
access unit has passed the
diagnostic test, and there
are no other status
messages.

No action needed; no problems
were found during power-up or
reset.

Record the failure code before resetting the access unit; otherwise, the error
information will be lost.

Содержание 9121









































































Результаты поиска

Содержание 9121

Отзывы:

Paradyne 9121, Руководство пользователя, Страница: 34 / 73

Результаты поиска

Содержание 9121

Отзывы: