Paradyne 9121 Скачать руководство пользователя страница 52

Страница: 52 / 73

Maintenance and Troubleshooting

5-2

9121-A2-GB20-00

June 1997

T1 Access Unit

Label

Indication

Color

What It Means

Power and
Operational
Status

Green

ON –

Access unit has power and is
operational.

OFF –

Access unit is in a power-up self-test,
or there is a failure.

Blinking ON and OFF ( Rate: 1 Hz ) –

Software is being downloaded.

ALM

Operational
Alarm ( Fail )

Red

ON –

Access unit has just been reset, or an
error or fault has been detected.

Error/fault/alarm conditions:

Out of Frame ( OOF )

Loss of Signal (LOS)

Alarm Indication Signal (AIS)

Exceeded Error Rate (EER)

Yellow Alarm Signal

Device Fail

DBM Card Failed

Memory Failed

T1 Failed

CPU Failed

ISDN Network Failed

LMI Down

DLCI Down

Network Communication Link Down

CTS Down to device

DTR Down to device

Download Failed

Primary or Secondary Clock Failed

OFF –

No failures have been detected.

Содержание 9121









































































Результаты поиска

Содержание 9121

Отзывы:

Paradyne 9121, Руководство пользователя, Страница: 52 / 73

Результаты поиска

Содержание 9121

Отзывы: