Paradox Spectra 1759EX V1.0, Справочное и монтажное руководство

Страница: 38 / 60

36
R
EFERENCE
& I
NSTALLATION
M
ANUAL
If Hexadecimals (0 to FF) are used to program the report codes, verify that the pager also supports
Hexadecimals. If the pager does not support Hexadecimals, use only the digits 0 to 9.
UL Note: The installer is required to verify the complete compatibility of the DAC Receiver and formats at least
once per year.
9.5.1 S
TANDARD
P
ULSE
F
ORMATS
The Spectra Control Panels can use the Ademco slow, Silent Knight and Sescoa standard pulse reporting formats (see
Table 10 above).
9.5.2 A
DEMCO
E
XPRESS
The Ademco Express is a high-speed reporting format, which will transmit the 2-digit (11 to FF) report codes
programmed into sections [160] to [213]. Unlike other Ademco formats, the Ademco Express does not use the Contact
ID Report Codes.
9.5.3 A
DEMCO
C
ONTACT
ID
Ademco Contact ID is a fast communicator format that uses tone reporting instead of pulse reporting. This communicator
format also uses a pre-defined list of industry standard messages and report codes that will suit most of your basic
installation needs. Please refer to the Contact ID Report Codes List in the Programming Guide for a complete list of these
report codes and messages.
9.5.4 C
ONTACT
ID O
PTIONS
Section [136]: Dialer Options
Option
[3]
OFF = Programmable Codes
Option
[3]
ON = All Codes (default)
When using the Programmable Codes format, use the Ademco Contact ID Report Codes List in the Spectra System
Programming Guide (version 2.0 or higher) to program the desired report codes into sections [160] to [213]. Enter FF
to use the default Contact ID Report Codes. Press the [
FORCE
] key to enter a 0 value. When using the All Codes
format, the control panel will automatically generate Contact ID Report Codes for every event in sections [160] to [213].
Refer to the “All Codes” Ademco Contact ID Report Code List in the Spectra System Programming Guide.
When using the Ademco Contact ID Programmable format, both telephone numbers must use this
reporting format.
9.5.5 P
AGER
R
EPORTING
F
ORMAT
Section [136]: Dialer Options
[6]
OFF /
[7]
OFF: 1 call to the pager/cellular telephone
[6]
OFF /
[7]
ON: 2 calls to the pager/cellular telephone
[6]
ON /
[7]
OFF: 3 calls to the pager/cellular telephone
[6]
ON /
[7]
ON: 4 calls to the pager/cellular telephone
Using this format allows the control panel to transmit report codes to a pager or a cellular telephone. Since the control
panel cannot confirm whether the transmission was successful or not, it can be programmed to call the pager or
cellular telephone up to four times and transmit the report codes each time. To ensure that the report is received, the
control panel transmits the account number, the report code and the # sign four times during each call. Also, refer to
the Pager Delay in section 9.6.
9.6 PAGER DELAY
Section [083]
001 to 255 seconds, default = 5 seconds
When using the Pager Reporting Format (see section 9.5.5), the control panel will wait for the Pager Delay period before
transmitting the report codes. This is to allow time for the pager system to provide a dial tone or to bypass the “welcome”
message before sending data.
Table 10: Reporting Formats
Value Entered Reporting Format
1 Ademco Slow (1400Hz, 1900Hz, 10BPS)
2 Silent Knight Fast (1400Hz, 1900Hz, 10BPS)
3 SESCOA (2300Hz, 1800Hz, 20BPS)
4 Ademco Express (DTMF 4+2)
5 (Default) Ademco Contact ID
6 Pager Format