Panasonic WH-SXF12D6E5 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 120

background image

52

12.2. Water Pump

12.2.1. Water Pump Control

1. Once the indoor unit is ON, the water pump will be ON immediately and no error judgement for 9 minutes. However, during

this 9 minutes operation, if there is any abnormality cause at outdoor or malfunction, the compressor should be OFF
immediately and restart delay after 3 minutes.

2. The system will start checking on the water flow level after operation start for 9 minutes. If water flow level is detected low

continuously for 10 secs, the water pump and compressor will be OFF permanently and OFF/ON control panel LED will blink
(H62 error occurs).

3. The water pump will remain ON when compressor OFF due to thermostat OFF.

12.3. Pump Down Operation

Purpose

Ensure the pump down operation when relocating or disposing of the unit. The pump down operation will extract all
refrigerant from the piping into the outdoor unit.

1. Make sure the OFF/ON control panel LED is OFF (no operation).
2. Press the Pump Down button to start the pump down operation.
3. No low pressure protection error during pump down operation and 3-way valve will be shift to heating side.
4. Press OFF/ON button to stop the pump down operation.

12.4. Flow Switch

12.4.1. Flow Switch Control

1. The water flow switch serve as an overload protector that shuts down the unit when the water level is detected to be low.
2. Detection is Lo (0V) when there is no water flow, and detection is Hi (5V) when there is water flow.

«
...
50
51
52
53
54
...
»

Содержание WH-SXF12D6E5

























































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SXF12D6E5

Бренд: NARVI Страницы: 12

Бренд: Panasonic Страницы: 55

Бренд: B+BTec Страницы: 20

Бренд: Bionaire Страницы: 8

Бренд: VonHaus Страницы: 10

Бренд: alkitronic Страницы: 12

Бренд: Endress Страницы: 17

Бренд: Gianneschi Страницы: 28

Бренд: Bard Страницы: 41

Бренд: VOLTOMAT HEATING Страницы: 104

Бренд: Rotex Страницы: 80

Бренд: Xylem Страницы: 8

Бренд: SKF Страницы: 12

Бренд: WACKER Group Страницы: 66

Бренд: Xylem Страницы: 20

Бренд: Reznor Страницы: 31

Бренд: INTELLI HEAT Страницы: 3

Cylinder DuroTech MAP07

Бренд: Milwaukee Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды