Panasonic WH-SXF12D6E5 Скачать руководство пользователя страница 44

Страница: 44 / 120

Case 1:
• THERMO OFF TEMP:

1. THERMO OFF TEMP = Heat pump tank target tempe

[+2 C]

2. Tank temperature > THERMO OFF TEMP for continuous 3 minutes, switch 3 ways valve to room side.

• Next THERMO ON TEMP:

1. THERMO ON TEMP = Heat pump tank target tempe

[-3 C]

2. If tank temperature < THERMO ON TEMP

AND

External Room Thermo OFF, switch to tank side.

Case 2:
• Heat pump THERMO OFF TEMP:

1. Heat pump THERMO OFF TEMP = 53 C +

[+4 C]

2. Water outlet temperature > Heat pump THERMO OFF TEMP for continuous 3 minutes, switch 3 ways valve to room

side.

• Next THERMO ON TEMP:

1. THERMO ON TEMP = Tank temp. when heat pump thermo off +

[-3 C]

2. If tank temperature < THERMO ON TEMP

AND

External Room Thermo OFF, switch to tank side.

Case 3:
• Heat pump THERMO OFF TEMP:

1. Water inlet temperature > 52 C for continuous 60 secs, switch 3 ways valve to room side.

• Next THERMO ON TEMP:

1. THERMO ON TEMP = Tank temp. when heat pump thermo off +

[-3 C]

2. If tank temperature < THERMO ON TEMP AND External Room Thermo OFF, switch to tank side.

Case 4 (Only during solar priority is set condition):
• When solar request ON, solar valve will ON and switch 3 ways valve to room side

• THERMO ON TEMP:

1. THERMO ON TEMP = Heat pump tank target tempe

[-3 C]

2. If tank temperature < THERMO ON TEMP AND External Room Thermo OFF

AND

Solar 3WV OFF, switch to tank

side.

3. Backup Heater control:-

a. During External Room Thermo ON time, follow normal backup heater control operation
b. During External Room Thermo OFF time, Backup heater OFF

4. Booster heater control:

• Booster heater On/Off follow normal operation.

* Under solar priority is set condition, when solar 3 way valve is ON, booster heater turn OFF.

5. Solar 3 way valve:

• Solar 3 way valve operates follow solar operation specification.

* Under solar priority is set condition, when solar 3WV turn ON, booster heater will turn OFF and 3 ways valve switch to room

side.

* Under solar priority is not set condition, solar 3WV will OFF when heat pump operate to tank side.

Содержание WH-SXF12D6E5

























































































































Результаты поиска

Содержание WH-SXF12D6E5

Отзывы:

Похожие инструкции для WH-SXF12D6E5

Бренды по названию

Популярные бренды

Panasonic WH-SXF12D6E5, Руководство по обслуживанию

Результаты поиска

Содержание WH-SXF12D6E5

Отзывы:

Похожие инструкции для WH-SXF12D6E5

Бренды по названию

Популярные бренды