Panasonic VB-44210G Скачать руководство пользователя страница 69

Страница: 69 / 394

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-23

• FF1 (System): DISA Outbound Call ID Code 1

• FF1 (System): DISA Outbound Call ID Code 2

• FF2 (Trunk): DISA Auto Answer

• FF2 (Trunk): DISA Start Time

• FF2 (Trunk): DISA End Time

To program an incoming code from an attendant phone:

In addition to the DISA ID Setting in FF1, the following procedure can be
used to program an incoming code.

1. Press

the

ON/OFF

key.

• The phone issues intercom dial tone.

• The

ON/OFF

LED lights.

2. Press

the

CONF

key.

3. Dial

“#7.”

4. Enter the DISA code.

5. Press

the

HOLD

key.

6. Press

the

ON/OFF

key.

The

ON/OFF

LED goes off.

Hardware Requirements

• An MFR card is required for DISA. The MFR card is required to detect

DTMF tones entered via the DISA connection.

Considerations

• DISA can be used to access extensions as well as outside numbers.

• Once an incoming DISA code is entered, you cannot blank it out without

entering the programming mode.

• Busy override cannot be used for a DISA line.

• With CPC-A and CPC-B Versions 2.0 to 2.1, DISA calls cannot access

hunt groups.

Содержание VB-44210G











































































































































































































































































































































































































Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды

Panasonic VB-44210G, Руководство пользователя

Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды