Panasonic VB-44210G Скачать руководство пользователя страница 176

Страница: 176 / 394

Chapter 4. Key Telephone Features

Section 700 - Operation

4-60

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

2. Press

the

REDIAL

key.

The last number dialed appears on the display.

3. Complete the call and replace the handset.

The line key LED changes from green to red and then goes off.

Considerations

• If the Auto Flash Redial feature is set, you can flash the outside line once

by pressing the

REDIAL

key at the busy tone. You can then redial the last

number dialed.

• The Last Number Redial feature can redial a number up to sixteen digits

long.

• A maximum of five chained Speed Dialing codes can be redialed. See

“One-Touch Keys” on page 4-74 for more information.

Line Appearances

(All Versions)

The DBS provides up to four types of line appearances, depending on the
CPC version used.

The following table summarizes how each type of line appearance is used:

Table 4-7. MCO and ML key definitions

Key

Definition

DSS/BLF Appear-
ances

DSS/BLF keys provide one-touch dialing, direct station selection
(DSS), and busy lamp fields (BLF) for extensions.

Direct Line (DL)
Appearances

DL keys are used to originate and receive calls over specific trunk
numbers.

Multi-CO (MCO)
Appearances

MCO keys are used to originate and receive CO calls.

Multi-Line (ML)
Appearances

ML keys are used to originate and receive CO line calls and intercom
calls.

Содержание VB-44210G











































































































































































































































































































































































































Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды

Panasonic VB-44210G, Руководство пользователя

Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды