Panasonic VB-44210G Скачать руководство пользователя страница 180

Страница: 180 / 394

Chapter 4. Key Telephone Features

Section 700 - Operation

4-64

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

An MCO key can be assigned to any of the pooled trunk groups. See “Pooled
Trunk Access” on page 4-81 for more information.

See “ML/MCO Separation” (page 4-65) for information on assigning both
ML and MCO keys to the same system (CPC-AII and CPC-B Version 4 or
higher).

Operation

Related Programming

• FF1 (System): Least Cost Routing (LCR) Access

• FF2 (Trunks): Pooled Trunk Access for Group “9”

• FF2 (Trunks): Pooled Trunk Access for Groups “81-86”

• FF3 (Extension): Forced Least Cost Routing

• FF5 (Keys): FF Key Assignments (all)

• FF8 (LCR) LCR Settings (all)

Considerations

• When all trunks in a group are busy, the corresponding MCO key lights

red.

• If LCR is enabled, MCO keys can be assigned for trunk group 89.

However, the FF keys will not light.

• Press the MCO key that flashes red to answer an outside call.

• There are seven groups of outside lines: 9 and 81-86.

Operation

Action

To originate a trunk call

Press an idle MCO key.

The key blinks (green) as the call is made.

To place a call on Exclusive Trunk Hold (page 4-37)

Press the MCO key.

To place a call on System Trunk Hold (page 4-18)

Press the

HOLD

key.

To transfer a call

Press

HOLD

, dial the destination exten-

sion, then press

PROG

Содержание VB-44210G











































































































































































































































































































































































































Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды

Panasonic VB-44210G, Руководство пользователя

Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды