Panasonic VB-44210G Скачать руководство пользователя страница 193

Страница: 193 / 394

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-77

6. Enter the telephone number.

7. Press

the

HOLD

key.

8. Press

the

ON/OFF

key.

The

ON/OFF

LED goes off.

To check a programmed One-Touch key:

1. Press

the

ON/OFF

key.

• The phone issues intercom dial tone.

• The

ON/OFF

LED lights.

2. Press

the

CONF

key.

“C” appears in the display.

3. Press the One Touch key to be checked.

The programmed data appears on the display.

4. Press

the

ON/OFF

key.

• The

ON/OFF

LED goes off.

• The date and time appears on the display.

Considerations

• If the pause following an access code is too short, press the

REDIAL

key

more than once.

• A One-Touch key can be programmed to automatically access a CO line

before dialing a personal speed dial number.

• Select an outside line group when you program a One-Touch key. A free

line is selected from that group when you dial out. (Group 9 can be
programmed to select LCR automatically.) The following table shows the
available outside line groups and their corresponding code numbers:

Содержание VB-44210G











































































































































































































































































































































































































Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды

Panasonic VB-44210G, Руководство пользователя

Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды