Panasonic VB-44210G Скачать руководство пользователя страница 53

Страница: 53 / 394

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-7

4. Enter the Answer Signal Code (1 to 5 digits).

5. Press

the

HOLD

key.

To view an answer signal code:

1. Press

the

ON/OFF

key.

2. Press

the

CONF

key.

3. Dial

“#94.”

Considerations

• The digits used for the answer signal code are determined by the

requirements of the voice mail system.

• If the called extension does not answer and is forwarded to voice mail, the

DBS sends a call forward ID code back to the voice mail system.

• During transmission of the answer signal code, other DTMF digits and

functions from the DBS extension are ignored.

Auto Day Mode

(CPC-AII prior to 7.0 and CPC-B Version 4.0 to 6.11)

Description

Auto Day Mode allows the DBS to go into day mode automatically.

The DBS can also be programmed to go into night mode automatically (see
“Night Service,” page 3-35).

If only one of the auto modes is turned on, the

NIGHT

key is used to turn off

the auto mode. For instance, if night mode has been activated automatically,
the attendant must press the

NIGHT

key to go into day mode.

If only one of the auto modes is turned on, the

NIGHT

key can also be used

to go into an auto mode before the scheduled time.

If both auto day and auto night modes are turned on, the attendant

NIGHT

key

cannot

be used.

Содержание VB-44210G











































































































































































































































































































































































































Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды

Panasonic VB-44210G, Руководство пользователя

Результаты поиска

Содержание VB-44210G

Отзывы:

Похожие инструкции для VB-44210G

Бренды по названию

Популярные бренды