Panasonic TH-43EQ2W Скачать руководство пользователя страница 75

Страница: 75 / 178

English

■

[Network control]

Set when controlling with the unit’s LAN terminal.

[Off]:

Invalidates control with LAN terminal.
(In this case, the power consumption of Standby

condition (when the power is turned off with the

remote control) will be slightly reduced.)

[On]:

Controls via LAN using the LAN terminal. The

power indicator lights purple when the power is

turned off with the remote control (standby).

Note

●

When using the LAN control function which is

described in “Using Network Function” (see page

‒

114), set this function to [On].

●

Even if the setting is set to [Off], the Web browser

control screens that do not control this unit (display

information [Status], detailed settings [Detailed set

up] and password change [Change password])

operate.

●

To enable the operation, set [Quick start] to [On].

●

When [Quick start] is set to [Off], the power can

be turned off via network control even if [Network

control] is set to [On]. However, the power cannot

be turned on from standby state with the exception

after a wake-up message (magic packet) is sent

from the network equipment in the network. To

control both, it is necessary to set both [Quick start]

and [Network control] to [On] respectively.

■

[PJLink settings]

Configure the PJLink settings to enable PJLink

communication on the unit.

PJLink settings

Password policy

Save

Password

PJLink control

PJLink notification
Notified IP address 1
Notified IP address 2

Off

192.168.0.100
192.168.0.101

[Password policy]:

Precautions for password settings of this item will be

displayed in a new window.

[PJLink control]:

Specifies the PJLink communication settings.

Off:

Disables PJLink control.

On:

Enables PJLink control.

[Password]:

The keyboard for setting the password is displayed.

After entering the password, select [Ok]; the

confirmation screen is displayed. Enter the password

again and select [Ok]; the password is determined.

●

Entering characters (see page 165)

[PJLink notification]:

Set this item when using the PJLink notification.

[Off]:

Disables the notification.

[On]:

Enables the notification.

[Notified IP address 1], [Notified IP address 2]:

Set the IP address of the PC where the status of this

unit is notified.

[Save]:

Saves the password determined above in the display

unit.

Note

●

Once determined, it is necessary to enter the

password to display the settings.

●

To set the setting to [On], you must configure

[Administrator account settings] in advance.

●

To use PJLink control, you need to set [On] to the

setting and set [Network control] to [On].

●

The password for the setting is different from the

password for [LAN setup].

■

[AMX D. D.]

Set whether to allow the Display to be detected by AMX

Device Discovery.

[Off]:

Disables detection by AMX Device Discovery.

[On]:

Enables detection by AMX Device Discovery.

●

For more details, visit the following web site.
http://www.amx.com/

Note

●

To set the setting to [On], you must configure

[Administrator account settings] in advance.

■

[Crestron Connected]

When this function is set to [On], the Display can be

monitored or controlled via the network using equipment

and application software of Crestron Electronics, Inc.
This Display supports the following application software

from Crestron Electronics, Inc.

•

Crestron Fusion

Crestron Connected is a function to connect to a system

developed by Crestron Electronics, Inc. which manages

and controls multiple system devices connected to the

network.

●

For details of Crestron Connected, refer to the

Crestron Electronics, Inc. web site (Provided only in

English).
http://www.crestron.com/

Note

●

To set the setting to [On], you must configure

[Administrator account settings] in advance.

Содержание TH-43EQ2W



















































































































































































Результаты поиска

Содержание TH-43EQ2W

Отзывы:

Похожие инструкции для TH-43EQ2W

Бренды по названию

Популярные бренды

Panasonic TH-43EQ2W, Руководство по эксплуатации

Результаты поиска

Содержание TH-43EQ2W

Отзывы:

Похожие инструкции для TH-43EQ2W

Бренды по названию

Популярные бренды