Panasonic PAW-VP1000LDHW Скачать руководство пользователя страница 82

Страница: 82 / 88

DHW PAW-VP - Installation manual – 2020-05

Electrical Heater

10.4 Checks Before Contacting Service

10.4.1 Factory pre-installed Back-up Heater

Trouble shooting

Before you contact your dealer, check following points:

Symptom

Cause

Remedy

Air-to-Water unit does not

run at all although power

is turned on.

Power failure or after power

failure Operation button is turned

off.

Fuse blown.

Improper temperature settings.

Press ON/OFF operation button on

remote controller again.
Switch on breaker if power is turned off.

If breaker has been tripped, consult your

dealer without turning it on.
If fuse is blown, consult your dealer.

If your Air-to-Water unit still does not work properly although you checked the points as de-

scribed above, first stop the operation and isolate the electrical supply. Then contact your dealer

and report the serial number and symptom.
Never repair your Air-to-Water unit by yourself, to do so may result in serious injury. The unit

must only be repaired by an authorised service agent.

You also report if the inspection mark



and the letters E, F, H, L, P in combination with the

numbers appear on the LCD of the remote control unit.
Should the power fail while the unit is running. If the power supply for this unit is temporarily cut

off, the unit will automatically resume operation once power is restored using the same settings

before the power was interrupted.

Содержание PAW-VP1000LDHW

























































































Результаты поиска

Содержание PAW-VP1000LDHW

Отзывы:

Похожие инструкции для PAW-VP1000LDHW

Бренды по названию

Популярные бренды

Panasonic PAW-VP1000LDHW, Руководство по установке

Результаты поиска

Содержание PAW-VP1000LDHW

Отзывы:

Похожие инструкции для PAW-VP1000LDHW

Бренды по названию

Популярные бренды