– 25 –
Chapter 2 Description of Parts — Shooting and recording/playback functions section
14 <STOP> (stop) button
Press this button to stop playback.
Also press it to stop interval recording and one-shot recording, or to
end combining of clips in one-clip recording.
When the screen other than the [HOME] screen of SmartUI is
displayed, the function corresponding to each setting screen is
executed.
15 <PLAY/PAUSE> (play/pause) button
Press this button to view the playback image using the viewfinder
screen or the monitor screen.
Pressing this button during playback pauses playback.
When the screen other than the [HOME] screen of SmartUI is
displayed, the function corresponding to each setting screen is
executed.
16 <LIGHT> button
Control lighting of SmartUI. Each press toggles lighting of SmartUI on
and off.
Display the [CAMERA] screen on SmartUI.
Display the [AUDIO] screen on SmartUI.
Display the [SETUP] screen on SmartUI.
Display the [HOME] screen on SmartUI.
21 <KEY LOCK> switch (page 135)
Disable button operations related to SmartUI and thumbnail
operations. However, <LIGHT> button operation is available.
22
<USB2.0> terminal (device) (page 146)
23
<USB2.0> terminal (host) (page 146)
Connect the USB 2.0 cable.
When the [PC MODE] item on the setting menu [PC/USB/LAN]
screen is set to [ON], data transfer using USB 2.0 is enabled.
In this state, recording/playback and clip operations on the camera
are limited.
24
P2 card insertion slot
25 P2 card access LED (page 33)
Indicate the access status of recording and playback of each card.
26 SD memory card insertion slot (page 82)
This is the insertion slot for the SD memory card (optional). Use the
SD memory card for recording/opening the setting menu and lens
files for the camera, or uploading metadata or proxy recording (extra-
cost option), etc.
@
@
NOTE
t
Cautions in using SD memory cards
- On the camera, use SD memory cards that are compliant with
the SD standard or the SDHC standard.
- MMC (Multi Media Card) cannot be used. (Bear in mind that
taking pictures may no longer be possible if you do use them.)
- When using miniSD/microSD cards with the camera, always
install the adaptor specially designed for miniSD/microSD
cards. (The camera will not work properly if only the miniSD/
microSD adaptor is installed. Make sure that the card has
been inserted into the adaptor before use.)
- Use of Panasonic SD memory cards and miniSD/microSD
cards is recommended. Be sure to format cards on the
camera before use.
- Any SD memory card with a capacity of 8 MB to 2 GB and any
SDHC memory card up to 32 GB can be used on the camera.
Also, when performing proxy recording (extra-cost option), use
SDHC memory cards or SD memory cards with a capacity of
256 MB to 2 GB marked “High Speed”, etc.
- For the latest information not available in the Operating
Instructions, visit the support desk at the following website:
http://pro-av.panasonic.net/
27
Busy (active status indication) lamp (page 83)
Indicate the active status of the SD memory card, and is illuminated
when the card is active.
@
@
NOTE
t
Do not insert or remove the card while the lamp is lit. This might
damage the SD memory card.
28 <SDI OUT/IN (OP)> terminal (page 49)
Output the SDI signal.
f
By installing the HD/SD SDI input board (optional), SDI signals can
be input. (page 167)
29 <MON OUT> terminal (page 49)
This is the video output terminal for the monitor. Video independent
from the <SDI OUT/IN (OP)> terminal can be output. Also, HD SDI
signal or down-converted SD SDI signal, or VBS signal can be
selected on the [SET02:MON/HDMI FORMAT] screen of SmartUI.
Cross-conversion and up-conversion are not supported.
30 <LAN> terminal (100BASE-TX)
Enabled when the network function (extra-cost option) is installed.
For the cable to be connected to the <LAN> terminal, use the
shielded cable.
32
<USB2.0> terminal (sub-host)
Attach the wireless module AJ-WM30 (optional). This can also be
used to attach a USB cable that connects the UPLINK device and
the camera when the optional Upgrade Software Key (AG-SFU603G:
UPLINK device control function (extra-cost option)) is installed.
33
<FOCUS ASSIST> button (page 80)
Turn on/off the function for enlarging the video at the center of the
screen.
