Panasonic MINAS A5 Series, Руководство по эксплуатации

Страница: 98 / 477

2-50
‡)ROORZWKHSURFHGXUHVEHORZIRUWKHZLULQJFRQQHFWLRQWRWKH&RQQHFWRU
XA
,
XB
and
XC
.
How to connect
1. Peel off the insulation cover of the cable.
‡)RUVLQJOHZLUH3OHDVHREH\WKHOHQJWKLQÀJXUH
‡)RUVWUDQGHGZLUHVIHUUXOHVPXVWEHXVHGDVLOOXVWUDWHGEHORZ
Example: Ferrules with plastic insulating sleeve
(AI series, Phoenix Contact, Ltd.)
1) Peel off the sheath so that the conductor portion of the
cable will protrude from the tip of the ferrule. (It should
protrude 1 mm or more from the ferrule.)
2) Insert the cable into the ferrule and crimp it with an ap-
propriate crimping tool.
3) After crimping, cut off the cable conductor portion pro-
truding from the ferrule. (The allowable protruding length
after cutting should be 0 to 0.5 mm.)
‡ Part No. of the crimping tool: CRIMPFOX U-D66 (1204436)
Available from Phoenix Contact, Ltd.
(1)
(2)
(3)
A
A＞B
1mm or more
B
Examples: Nylon-insulated ferrule
(NTUB series, J.S.T. Mfg. Co., Ltd.)
Vinyl-insulated ferrule
(VTUB series, J.S.T. Mfg. Co., Ltd.)
1) Peel off the sheath of the cable conductor
portion to the length equal to that of sheath
on the ferrule.
2) Insert the cable into the ferrule and crimp it
with an appropriate crimping tool.
‡3DUW1RRIWKHFULPSLQJWRRO<17
Available from J.S.T. Mfg. Co., Ltd
①
②
A
A≧B A≦B＋C
B C
‡:KHQSHHOLQJRIIWKHVKHDWKRIWKHFDEOHWDNHFDUHQRWWRGDPDJHRWKHUSRUWLRQV
‡:KHQFULPSLQJWKHIHUUXOHVXIÀFLHQWO\FKHFNWKHVWDWXVRIWKHIHUUXOHDQGFDEOH,IWKHFRQGXFWRUVRIWKH
cable stick out from the insulation cover or protrude excessively from the tip of the ferrule, accidents
VXFKDVDQHOHFWULFVKRFNDQGÀUHIURPDVKRUWFLUFXLWPD\UHVXOW
2. Insert the cable to the connector in the following 2 methods.
(a) Insert the cable using the supplied handle lever.
E,QVHUWWKHFDEOHXVLQJDÁDWEODGHVFUHZGULYHU(GJHZLGWKWRPP
Attach the handle lever to the
handling slot on the upper
portion. Press down the lever
to push down the spring.
Insert the peeled cable while
pressing down the lever, until
it hits the insertion slot
(round hole).
Release the lever.
Press the screw driver to the
handling slot on the upper
portion to push down the
spring.
Insert the peeled cable while
pressing down the screw
driver, until it hits the
insertion slot (round hole).
Release the screw driver.
(a) Using handle lever (b) Using screw driver
*
You can pull out the cable
by pushing down the spring
as the above.
1
2
3
1
2
3
8 to 9 mm
‡7DNHRIIWKHFRQQHFWRUIURPWKH6HUYR'ULYHUEHIRUHPDNLQJFRQQHFWLRQ
‡,QVHUWRQO\RQHFDEOHLQWRHDFKRQHRIFDEOHLQVHUWLRQVORW
‡3D\DWWHQWLRQWRLQMXU\E\VFUHZGULYHU
2
Preparation
2.
6\VWHP&RQÀJXUDWLRQDQG:LULQJ
Wiring method to connector
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com