![background image](http://html1.mh-extra.com/html/panasonic/aw-ue150kp/aw-ue150kp_operating-instructions-manual_3701238128.webp)
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching between [Fan1] and [Fan2]
- After switching [OSD Mix]
- After switching [Tally]
- After moving the crop frame of [Crop Mode]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Reset to the default (Except the network
settings)] of [Maintenance]
IP(UDP) [On, Off]
Sets the UDP output function [On] or [Off] to output tracking data,
such as Pan/Tilt/Zoom or other information from the IP output,
synchronized with the Genlock signal. (→ page 62)
When [IP(UDP)] is set to [On], a warning message is displayed. Click
the [OK] button to enable the settings.
Factory settings:
Off
<NOTE>
• When [IP(UDP)] is [On], video transmission via IP may be delayed
or the video may suffer frame loss.
We recommend setting [IP(UDP)] to [Off] to avoid the delay or frame
loss due to the video transmission via IP.
• In the following cases, the tracking data output may be delayed or
the value may not be updated.
- When performing video transmission via IP (M-JPEG/H.264/H.265/
RTMP/RTMPS/NDI|HX/SRT)
- When opening the web screen (live screen [Live] or the web
setting screen [Setup])
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed
between Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color Temperature Setting]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching between [Fan1] and [Fan2]
- After switching [OSD Mix]
- After switching [Tally]
- After moving the crop frame of [Crop Mode]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Reset to the default (Except the network
settings)] of [Maintenance]
Invert Pan/Tilt Axis [Off, On]
Sets whether to invert the Pan/Tilt data for output in the tracking data.
Off
Pan/Tilt data is not inverted.
On
Pan/Tilt data is inverted for output.
Factory settings:
Off
z
IP out
Output client select [Client 1 to 4]
Enable or disable up to four clients to forward the tracking data when
[IP(UDP)] is [On].
Forwards the tracking data via UDP such as Pan/Tilt/Zoom or other
information to the clients that are set to enable on this screen.
The setting is confirmed with the [Set] button.
Factory settings:
Client1: Disable
Client2: Disable
Client3: Disable
Client4: Disable
<NOTE>
• Disable the client that does not require the forwarding of the tracking
data because the UDP packet is transmitted to the enabled client at
the system frequency interval.
• When multiple clients are enabled, the timing of transmitting the
UDP packet to the second and subsequent clients will always be
delayed relative to the Genlock signal.
(Approximately 200 to 300 μs delay will occur for each client. The
latency may be increased depending on the system status or the
network environment of the unit.)
Client1 to 4
IP address(IPv4)
Sets the destination IP address to forward the tracking data such as
Pan/Tilt/Zoom or other information via UDP.
The setting is confirmed with the [Set] button.
Factory settings:
Client1: 192.168.0.111
Client2: 192.168.0.112
Client3: 192.168.0.113
Client4: 192.168.0.114
<NOTE>
• The address to forward the tracking data can only be configured
as IPv4.
• A multicast address cannot be specified for the destination
address.
128
Web screen configurations (continued)