![background image](http://html1.mh-extra.com/html/panasonic/aw-ue150kp/aw-ue150kp_operating-instructions-manual_3701238061.webp)
Tracking data output
When [Serial] or [IP] of [Tracking Data Output] on the [System 2/2]
screen is set to [On], outputs the tracking data for Pan/Tilt/Zoom or other
information to link with a virtual studio system or elsewhere via serial
(RS-422) or IP output.
z
Serial (RS‑422) output
• When [Serial] of [Tracking Data Output] on the [System 2/2] screen is
set to [On], the tracking data for Pan/Tilt/Zoom or other information is
synchronized with the Genlock signal and output via the serial output
(RS-422).
• The tracking data is output in stream mode in a format conforming to
the free-d protocol. The message type is Type D1 (camera position/
orientation data) only.
Advanced stored data
This unit stores and outputs the following data according to the packet
structure specified in Type D1 of the free-d protocol.
Camera ID
An ID between 00h and FFh can be selected.
Camera Pan Angle
Stores the Pan angle of the unit (–175° to +175°) with the format
provided by the free-d protocol.
Camera Tilt Angle
Stores the Tilt angle of the unit (–30° to +210°) with the format
provided by the free-d protocol.
<NOTE>
• The range of the angle is limited to between –90° and +90° in the
free-d protocol. However, this unit can store greater angles than
+90° (up to +210°).
Camera Roll Angle
Stores the rotation angle (0° or 180°) corresponding to the flip state
(turned upside down or left-right reversed) of the unit with the format
provided by the free-d protocol.
Stores an angle of 180° in the flipped state (turned upside down
or left-right reversed) (exceeding the angle specified when [Smart
Picture Flip] is [On]), and stores 0° other than in this condition.
Camera X‑Position
Always stores 000000h.
Camera Y‑Position
Always stores 000000h.
Camera Height (Z‑Position)
Always stores 000000h.
Camera Zoom
Stores the magnification of optical zoom of this unit between 000555h
(WIDE) and 000FFFh (TELE).
<NOTE>
• The magnification of digital zoom is not stored.
Camera Focus
Stores the value of focus position of this unit between 000555h
(NEAR) and 000FFFh (FAR).
Spare / User Defined (16bits)
Stores the value of iris position of this unit between 0555h (CLOSE)
and 0FFFh (OPEN).
Checksum
Stores the checksum value provided by the free-d protocol.
<NOTE>
• The serial connection of the remote controller (AW-RP150, etc.)
cannot be made if [Serial] is already [On].
• In the following cases, the tracking data output may be delayed or the
value may not be updated.
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed between
Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color TEMP. Setting]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching between [Fan1] and [Fan2]
- After switching [OSD Mix]
- After switching [Tally]
- After moving the crop frame of [UHD Crop]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Initialize] of [Maintenance]
60
61
Camera menu items (continued)