20
Parts and their functions
(continued)
i
LAN connector for IP control [LINK/ACT]
This LAN connector (RJ-45) is connected when exercising
IP control over the unit from an external device.
Use a cable with the following specifications for the
connection to the LAN connector:
When connecting through a hub:
LAN cable
* (category 5 or above),
max. 100 meters [328 ft]
When using a PoE+ compatible hub:
LAN cable
* (category 5e or above),
max. 100 meters [328 ft]
When a hub is not used:
LAN cable
* (category 5 or above),
max. 100 meters [328 ft]
*: Use of an STP (shielded twisted pair) cable is
recommended.
j
Anti‑theft wire mounting hole
Use this hole to attach the wire bracket (commercially
available).
k
Audio input connector [AUDIO IN]
Inputs external audio (microphone, line).
l
RS‑232C connectors [RS‑232C IN/OUT]
Connect to RS-232C cables.
RS‑232C IN/OUT
connector
1
2
3
4
5
6
7
8
●
Mini DIN 8‑pin
(JST)
RS‑232C IN
RS‑232C OUT
Pin
No.
Signal
Pin
No.
Signal
1
DTR_IN
1
DTR_OUT
2
DSR_IN
2
DSR_OUT
3
TXD_IN
3
TXD_OUT
4
GND
4
GND
5
RXD_IN
5
RXD_OUT
6
GND
6
GND
7
IR OUT R
7
NC
8
IR OUT L
8
NC
●
Be aware that the polarities (+/−) of the serial data
may be different depending on the specifications of
the device to be connected.
Note
m
DC IN connector [12V IN
]
Connect the AC adaptor supplied with the unit to this
connector to supply the DC 12 V voltage to the unit.
n
Cable clamp
This is used to hold the cable connection to the DC IN
connector and prevent it from becoming disconnected.
o
Ground connector
Connects to the ground connector on a wall outlet,
ground bar, etc. for grounding. (Installation Instructions
→
“Connections”
→
“Note on grounding”)
p
RS‑422 connector [RS‑422]
This RS-422 connector (RJ-45) is connected when
exercising serial control over the unit from an external
device.
Use a cable with the following specifications for the
connection to this connector.
The tally lamp can be lit by shorting the TALLY signal (pin
2) with GND (pin 1).
●
Do not apply a voltage to the TALLY signal pin.
Note
LAN cable
* (category 5 or above, straight cable), max.
1000 meters [3280 ft]
*: Use of an STP (shielded twisted pair) cable is
recommended.
1 3 5 7
2 4 6 8
Pin
No.
Signal
Pin
No.
Signal
1
GND
5
TXD +
2
TALLY
6
RXD +
3
RXD –
7
—
4
TXD –
8
—
q
USB port
The unit can be used as a Web camera by connecting the
unit and a personal computer with USB Video Class.
r
microSD card slot
The video and audio of the camera can be recorded to a
microSD card in MP4 format.
s
Threaded hole (thread: 1/4‑20UNC, ISO1222
[6.35 mm]) for mounting the camera
Use this hole when mounting the camera on a tripod, etc.
t
HDMI connector [HDMI]
This is the HDMI video signal output connector.
For limitations that pertain when simultaneously outputting
HDMI and SDI signals, refer to page 55.
u
SDI OUT connector [SDI OUT]
This is the SDI video signal output connector.
For limitations that pertain when simultaneously outputting
HDMI and SDI signals, refer to page 55.
