Panasonic AJSDX900P - 24P DVCPRO 50, Руководство по обслуживанию

Страница: 124 / 421

ELE-11
2-16. Standard Sensitivity Adj.
(P mode)
BOARD PREPROCESS Board
TP TP103 (R), TP303 (G), TP503 (B)
ADJ. EVR
F No. F11 + 1/2 (2,000lux)
CHART Gray Scale
MODE CAM
M. EQ. Oscilloscope
SPEC. A = 1,000mVp-p
±
10mV
1. Click
the “15. Standard Sensitivity Adjustment P
mode” of the camera adjustment software.
2. Connect a scope to TP103 (R-ch) and adjust the Slider
on the PC (EVR) so that the level (A) becomes
1,000mVp-p
±
10mV as shown in 2-15.
3. Click “>>” .
4. Connect a scope to TP303 (G-ch) and adjust the Slider
on the PC (EVR) so that the level (A) becomes
1,000mVp-p
±
10mV as shown in 2-15.
5. Click “>>” .
6. Connect a scope to TP503 (B-ch) and adjust the Slider
on the PC (EVR) so that the level (A) becomes
1,000mVp-p
±
10mV as shown in 2-15.
7. Click “>>” .
8. After compleate the adjustment, click “NORMAL 60I
(for NTSC) ” or “NORMAL 50I (for PAL) ” .
2-17. Sub Voltage Adj.
BOARD DRIVE Board
TP VIDEO OUT (75 ohm terminated)
ADJ. EVR
F No. F11 + 1/2 (2,000lux)
CHART -
MODE CAM
M. EQ. Monitor TV, Oscilloscope
SPEC. No Blooming
1. Set the shutter 1/2,000.
2. Shoot a 500W halogen light and set the zoom position
so that the halogen light size is approximately 1/10 of
the vertical direction of the monitor as shown figure.
3. Click the “16. Sub Voltage Adjustment” of the
camera adjustment software.
4. Adjust the slider so that the blooming is disappeared at
the any position of the monitor screen as shown figure.
5. Click “>>” .
6. Adjust the slider so that the blooming is disappeared at
the any position of the monitor screen as shown figure.
7. Click “>>” .
8. Adjust the slider so that the blooming is disappeared at
the any position of the monitor screen as shown figure.
9. Click “>>” .
10.
Connect a oscilloscope to TP103 (R), TP303 (G),
TP503 (B) and confirm that the level of saturation is
more than 450%. If the level of saturation is under
450%, adjust again.
2-18. Sub Voltage Adj. (P mode)
BOARD DRIVE Board
TP VIDEO OUT (75 ohm terminated)
ADJ. EVR
F No. F11 + 1/2 (2,000lux)
CHART -
MODE CAM
M. EQ. Monitor TV, Oscilloscope
SPEC. No Blooming
1. Set the shutter 1/2,000.
2. Shoot a 500W halogen light and set the zoom position
so that the halogen light size is approximately 1/10 of
the vertical direction of the monitor as shown in as
shown in 2-17.
3. Click the “17. Sub Voltage Adjustment P mode” of
the camera adjustment software.
4. Adjust the slider so that the blooming is disappeared at
the any position of the monitor screen as shown figure.
5. Click “>>” .
6. Adjust the slider so that the blooming is disappeared at
the any position of the monitor screen as shown figure.
7. Click “>>” .
8. Adjust the slider so that the blooming is disappeared at
the any position of the monitor screen as shown figure.
9. Click “>>” .
10. After compleate the adjustment, click “NORMAL 60I
(for NTSC) ” or “NORMAL 50I (for PAL) ” .
10
1
Blooming
Monitor (VIDEO OUT)
halogen lamp