Palax C750 Ergo Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 34

background image

12

Palax C750

Translation

1-2018

longer be considered to correspond to its original configuration.

Other possible expenses or financial claims due to the above-mentioned
measures.

any indirect costs and/or travel expenses incurred from making repairs under the
guarantee.

For parts changed during the warranty period, the warranty expires at the same time as
the warranty period of the machine.

Consult your dealer about matters related to the warranty.

1.12

Operating instructions for the winch

Please refer to the user manual of the winch or visit our website at www.palax.fi for more
detailed operating instructions for the winch.

2

TAKING DELIVERY AND SETTING UP THE MACHINE FOR
OPERATION

2.1

Lifting the machine

There are lifting lugs for lifting the machine with a crane at both ends of the machine, at
the rear edge of the splitting chute and at the rear edge of the infeed deck.

The machine can be lifted with a forklift truck from both sides. There are guide rails for
lifting forks under the chassis.

2.2

The transport set-up and unpacking

The machine is delivered almost ready assembled and with the conveyor attached.

In order to avoid damage during transportation, the machine is delivered partly
dismantled so that all the protruding levers and the hitching parts of a tractor-powered
machine have been removed and packed separately.

The extension table for the infeed conveyor and the loading conveyor are in the
transport position.

The angular gear is filled with transmission oil.

2.3

Acceptance inspection

Check the delivered goods without delay.

If the product shows transport damage, contact the transport company and your dealer
immediately.

2.4

Main parts of the machine, Fig 1

1.  Infeed conveyor support
2.  Infeed conveyor belt
3.  In-feed conveyor
4.  Conveyor support
5.  Emergency stop lever, tractor-powered machine
6.  Blade cover
7.  Multi-function lever, crosscut and infeed operations
8.  Protective net for splitting chute
9.  Adjustment lever 12 for the splitting wedge
10. Conveyor

«
...
10
11
12
13
14
...
»

Содержание C750 Ergo



































Отзывы:

Нет отзывов

Похожие инструкции для C750 Ergo

Бренд: AAVIX Страницы: 21

Бренд: Zipper Mowers Страницы: 45

Michel 80 30 29

Бренд: Westfalia Страницы: 19

Бренд: Boss Industrial Страницы: 24

Бренд: Boss Industrial Страницы: 27

Бренд: Boss Industrial Страницы: 28

Бренд: Boss Industrial Страницы: 36

Бренд: Racing Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды