Palax C750 Ergo Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 34

background image

19

Palax C750

Translation

1-2018

WARNING! Never remove from the machine the plate that prevents the
simultaneous operation in two modes. Always remove the power take-off shaft
before operating the machine by electricity.

3.9

Operation under cold conditions

When an electric motor-powered machine is operated in temperatures below -15 degrees
Centigrade, the use of a less viscous hydraulic oil is recommended, because a machine
with electric drive takes full revolutions right from the start of operation. Suitable oils are,
for example, ISO VG22S multigrade oil or synthetic hydraulic fluid.

Electric heater for oil tank, Fig.12

A 300 W electric heater carpet with adhesive tape attachment and thermostat is
available as an option for the hydraulic oil tank.

The starter comes as standard equipped with operating switch for the heater. Fig 10C.

Heating the oil for 1-2 hours is sufficient to enable smooth starting.

The size of the heater carpet is 200 x 300 mm.

Capacity 300 W.

Equipped with thermostat.

Strongly adherent glue for attachment of the carpet.

12

NOTE !

Only a skilled craftsman is allowed to carry out electrical work for the

heater.

11

A

B

C

«
...
17
18
19
20
21
...
»

Содержание C750 Ergo



































Отзывы:

Нет отзывов

Похожие инструкции для C750 Ergo

Бренд: Palax Страницы: 34

SplitMaster 40123300

Бренд: SpeeCo Страницы: 16

Бренд: Wallenstein Страницы: 20

Бренд: Clarke Страницы: 24

Бренд: Swisher Страницы: 20

Бренд: Swisher Страницы: 40

Electric Logsplitter

Бренд: Redgum Страницы: 20

Бренд: Maxim Страницы: 12

Бренд: BE Страницы: 32

Бренд: Powerhouse Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды