Palax C750 Ergo Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 34

background image

18

Palax C750

Translation

1-2018

NOTE !

Only a skilled craftsman is allowed to change the direction of rotation.

NOTE !

Only use an extension cord equipped with a changeover switch for

rotation direction of the motor that can be turned by screwdriver.

3.6

Starting the electric motor

Press the start button. In the Y-position the motor starts rotating at slow speed with low
output. The start phase takes several tens of seconds.

As the engine speed increases, the D-position is switched on and the motor quickly
reaches full speed. As the motor reaches full revolutions, the signal light on the starter
illuminates.

NOTE !

The machine must not be operated until the motor is running at full

speed.

3.7

Emergency stop of a machine powered by electric motor, Figure 10

Push down the emergency stop button B.

Turn the pushbutton clockwise to release it.

3.8

The machine is equipped with a system to prevent simultaneous operation

in two modes, Fig. 11

When the cover plate C is turned down, it is possible to connect the extension cord.
When the cover is turned up, it is possible to connect the PTO shaft.

Suspension hook A for the power take-off shaft.

A

10

C

B

«
...
16
17
18
19
20
...
»

Содержание C750 Ergo



































Отзывы:

Нет отзывов

Похожие инструкции для C750 Ergo

Бренд: Scheppach Страницы: 45

Бренд: Scheppach Страницы: 144

Бренд: DOSKO Страницы: 40

Бренд: Toro Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды