background image

 

FOR YOUR SAFETY READ BEFORE LIGHTING 

 

 

 

 

 

 

LIGHTING INSTRUCTIONS 

 

 

 

 

TO TURN OFF GAS APPLIANCE 

WARNING: 

If you do not follow these instructions exactly, a 

fire or explosion may result causing property damage, 
personal injury or loss of life. 

A. This appliance is equipped with an ignition device which 

automatically lights the pilot. Do not try to light the pilot by hand. 

B. BEFORE LIGHTING smell all around the appliance area for gas. Be 

sure to smell next to the floor because some gas is heavier than 
air and will settle on the floor.  
WHAT TO DO IF YOU SMELL GAS: 
- Do not try to light any appliance. 
- Do not touch any electric switch; do not use any phone in your 
building. 

- Immediately call your gas supplier from a neighbour's phone. Follow 
the gas supplier's instructions. 
- If you cannot reach your gas supplier, call the fire department. 

C. Use only your hand to push in or turn the gas control knob. Never use 

tools. If the knob will not push in or turn by hand, don't try to repair it, 
call a qualified service technician. Force or attempted repair may 
result in a fire or explosion. 

D. Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect the 
appliance & to replace any part of the control system & any gas 
control which has been under water. 

1. STOP! Read the safety information above on this label. 
2. This appliance is equipped with an ignition device which 

automatically lights the pilot. Do not try to light the pilot by hand. 

3. Push the "On/ Off" switch to turn the fireplace ON. 

- If the burner does light go to step 6. 
- If the burner does not light, complete steps 4 through 5. 
- If the burner will not light or stay lit after several tries, push the 
"On/ Off" switch for the fireplace to OFF, turn off all electric power  

to the fireplace and call your service technician or gas supplier. 
Note: Sufficient time must be allowed for air to escape from lines if 
the unit is being lit for the first time. 

4. Push the "On/ Off" switch to the fireplace Off. 
5.  Allow sufficient length of time (minimum 5 minutes) for any gas in the 

combustion chamber to escape. If you still smell gas, STOP! Follow 
"B" in the safety information above on this label. If you don't smell 
gas, go to step 3. 

6. Set fireplace to desired setting by using hand held remote. 

 

1.

 

Push the "on/ off" switch to the "Off" position.

 

2.  Turn off all electric power to the appliance and remove backup 

batteries if service is to be performed or for extended shutdown. 

                                   Hot while in operation. Do not touch. Severe burns may
result. Keep children, clothing, furniture, gasoline and other liquids having 
flammable vapours away. Keep burner and control compartment clean. See 
installation and operating instructions accompanying the appliance.

                                          L’appareil est chaud lorsqu’il fonctionne. Ne pas 
toucher l’appareil. Risque de brûlures graves. Serveiller les enfants. Garder les 
vêtements, le meubles, l’essence ou autres liquides produisant des vapeurs
inflammables loin de l’appareil. S’assurer que le brûleuret le compartiment des 
commandes sont propres. Voir les instructions d’installation et d’utilisation qui
accompagnent l’appareil.

CAUTION:

ATTENTION

Due to high surface temperatures, keep children, clothing and furniture away. Keep burner and 
control compartment clean. See installation and operating instructions accompanying the 
appliance.

A cause de la temperature elevee des parios, tenir eloignes les enfants, les vetements et les 
meubles. Maintenir propres le brûleur et le compartiment de commande. Voir les instructions 
relatives a l’installation et au fonctionnement qui accompagnent l’appareil.

5052.980-A

The lighting instructions label is located on the back of the gas valve controller caddy (Figure 106). It 

is accessed by removing the front and surround and then pulling the caddy out to reveal the lighting 
instruction label.

Figure 106:  Lighting instructions label location.

 Lighting Instructions 

42

051119-48 100000300

i40 TOFINO

Содержание Tofino Series

















































Отзывы: