![background image](http://html1.mh-extra.com/html/omron/sysmac-c200hs/sysmac-c200hs_operation-manual_742436168.webp)
158
Description
When the execution condition is OFF, ASFT(17) does nothing and the program
moves to the next instruction. When the execution condition is ON, ASFT(17) is
used to create and control a reversible asynchronous word shift register be-
tween St and E. This register only shifts words when the next word in the register
is zero, e.g., if no words in the register contain zero, nothing is shifted. Also, only
one word is shifted for each word in the register that contains zero. When the
contents of a word are shifted to the next word, the original word’s contents are
set to zero. In essence, when the register is shifted, each zero word in the regis-
ter trades places with the next word. (See Example below.)
The shift direction (i.e. whether the “next word” is the next higher or the next low-
er word) is designated in C. C is also used to reset the register. All of any portion
of the register can be reset by designating the desired portion with St and E.
Control Word
Bits 00 through 12 of C are not used. Bit 13 is the shift direction: turn bit 13 ON to
shift down (toward lower addressed words) and OFF to shift up (toward higher
addressed words). Bit 14 is the Shift Enable Bit: turn bit 14 ON to enable shift
register operation according to bit 13 and OFF to disable the register. Bit 15 is the
Reset bit: the register will be reset (set to zero) between St and E when
ASFT(17) is executed with bit 15 ON. Turn bit 15 OFF for normal operation.
Flags
ER:
The St and E words are in different areas, or St is greater than E.
Indirectly addressed DM word is non-existent. (Content of
∗
DM word is
not BCD, or the DM area boundary has been exceeded.)
Example
The following example shows instruction ASFT(17) used to shift words in an
11-word shift register created between DM 0100 and DM 0110 with a control
word value of #6000 (bits 13 and 14 ON). The data changes that would occur for
the given register and control word contents are also shown.
ASFT(17)
#6000
DM 0100
DM 0110
00000
Address
Instruction
Operands
00100
LD
00000
00101
ASFT(17)
#
6000
DM
0100
DM
0110
1234
0000
0000
2345
3456
0000
4567
5678
6789
0000
789A
Before
execution
DM 0100
DM 0101
DM 0102
DM 0103
DM 0104
DM 0105
DM 0106
DM 0107
DM 0108
DM 0109
DM 0110
1234
0000
2345
0000
3456
4567
0000
5678
6789
789A
0000
1234
2345
3456
4567
5678
6789
789A
0000
0000
0000
0000
After 1
execution
After 7
executions
5-16 Data Movement
This section describes the instructions used for moving data between different
addresses in data areas. These movements can be programmed to be within
the same data area or between different data areas. Data movement is essential
for utilizing all of the data areas of the PC. Effective communications in Link Sys-
tems also requires data movement. All of these instructions change only the
content of the words to which data is being moved, i.e., the content of source
words is the same before and after execution of any of the data movement in-
structions.
Data Movement
Section 5-16
Содержание SYSMAC C200HS
