![background image](http://html1.mh-extra.com/html/omron/sysmac-c200hs/sysmac-c200hs_operation-manual_742436025.webp)
12
7. Transfer the program and and any other require data to the C200HS. You
will probably want to transfer DM data and the I/O table, if you have created
an I/O table for the C200H.
8. Turn the C200HS off and then back on to reset it.
9. Test program execution before attempting actual operation.
Using Memory Cassettes
The following procedure outlines the steps to transfer C200H programs to the
C200HS via EEPROM or EPROM Memory Cassettes. This will allow you to read
the program data from the Memory Cassette automatically at C200HS startup.
The first four steps of this procedure is the same as those used for transferring
directly to the C200HS’s internal memory (UM area).
1, 2, 3...
1. Transfer the program and any other required data to the LSS work area. This
data can be transferred from a C200H CPU, from floppy disk, or from a
C200HS Memory Unit.
To transfer from a C200H CPU, set the PC for the LSS to the C200H, con-
nect the LSS to the C200H, go online, and transfer the program and any oth-
er require data to the LSS work area. You will probably want to transfer DM
data and the I/O table, if you have created an I/O table for the C200H.
or
To transfer from floppy disk, set the PC for the LSS to the C200H in the offline
mode and load the program and any other require data to the LSS work
area. You will probably want to load DM data and the I/O table, if you have
created an I/O table for the C200H.
or
To transfer from a C200H-MP831, set the PC for the LSS to the C200H in the
offline mode and read data from the Memory Unit into the LSS work area.
2. Go offline if the LSS is not already offline.
3. Change the PC setting for the LSS to the C200HS.
4. If you want to transfer I/O comments together with the program to the
C200HS, allocate UM area for I/O comments.
5. Allocate expansion DM words DM 7000 to DM 7999 in the UM area using the
UM allocation operation from the LSS.
6. Copy DM 1000 through DM 1999 to DM 7000 through DM 7999.
7. Write “0100” to DM 6602 to automatically transfer the contents of DM 7000
through DM 7999 to DM 1000 through DM 1999 at startup.
8. To transfer to an EEPROM Memory Cassette, use the following procedure.
a) Connect the LSS to the C200HS and go online.
b) Make sure that pin 1 on the C200HS’s CPU is OFF to enable writing to
the UM area.
c) Transfer the program and any other require data to the C200HS. You will
probably want to transfer DM data and the I/O table, if you have created
an I/O table for the C200H. Make sure you specify transfer of the Expan-
sion DM Area and, if desired, the I/O Comment Area.
d) Turn ON SR 27000 from the LSS to transfer UM data to the Memory Cas-
sette and continue from step 9.
or
To transfer to an EPROM Memory Cassette, use the following procedure.
a) Connect an PROM Writer to the LSS and write the data to the EPROM
chip using the LSS EPROM writing operation.
e) Set the ROM type selector on the Memory Cassette to the correct capac-
ity.
f) Mount the ROM chip to the Memory Cassette.
g) Mount a EPROM Memory Cassette to the C200HS.
9. Turn ON pin 2 on the C200HS’s DIP switch to enable automatic transfer of
Memory Cassette data to the CPU at startup.
New C200HS Features
Section 1-8
Содержание SYSMAC C200HS
