![background image](http://html1.mh-extra.com/html/omron/smartslice-grt1-drt/smartslice-grt1-drt_operation-manual_742293024.webp)
4
Slice I/O Terminal Introduction
Section 1-1
Contact Operation
Counter
This function can count the number of times each input or output contact
changes from OFF to ON (maximum resolution: 50 Hz). A warning set value
can be set in the Unit to monitor the number of contact operations, and turn
ON a warning flag in the Status Area when the set value is reached. The Con-
figurator or explicit messages can be used to read the information.
Note
The Contact Operation Counter and Total ON Time Monitor cannot be used at
the same time for a single contact.
Total ON Time Monitor
This function can record the total ON time of devices connected to the Unit,
such as sensors and relays. The total time is stored in the Unit and can be
read by the Configurator or explicit messages. A warning set value can be set
in the Unit to monitor the total ON time, and turn ON a warning flag in the Sta-
tus Area when the set value is reached.
Note
The Total ON Time Monitor and Contact Operation Counter cannot be used at
the same time for a single contact.
Operation Time Monitor
This function can measure and monitor an Input Unit’s operating time. The
time required for a bit to go ON or OFF can be measured at high speed within
the Unit, so that ladder programming is not required to measure the operating
time. The trigger edge (ON
→
OFF or OFF
→
ON), input number, and output
number can be selected freely, providing flexibility when testing. A warning
set value can be set in the Unit to monitor the operating time, and turn ON a
warning flag in the Status Area when the set value is reached.
Analog I/O Unit Features
Setting the Number of AD
Conversion Points
The conversion cycle when both analog input points are used is 2.42 ms max.
The AD conversion cycle can be shortened by reducing the number of points
used (i.e., the number of AD conversion points).
Moving Average
Analog Input Terminals can calculate the average of the past eight analog
input values to produce a stable input value even when the input value is
unsteady.
Scaling
Scaling allows values to be converted according to the industry unit required
by the user. It reduces the number of operations requiring ladder program-
ming in the Master CPU Unit. Scaling also supports an offset function for com-
pensating for errors in scaled values.
Peak/Bottom Hold
The maximum (peak) and minimum (bottom) values input to Analog Input Ter-
minals can be held. These values can then be compared with alarm set val-
ues, and flags turned ON accordingly to indicate the status (comparator
function).
Top/Valley Hold (Input
Units Only)
The top and valley values for values input to Analog Input Terminals can be
held. The timing of tops and valleys can be monitored with the Top/Valley
Detection Timing Flags. The top and valley values can be compared with
alarm set values, and flags turned ON accordingly to indicate the status (com-
parator function).
Rate of Change
The rate of change for values input to Analog Input Terminals can be obtained
for each sampling cycle.
Comparator
Values input to Analog Input Terminals or values after math processing can
be compared to the alarm set values (HH, H, L, and LL), and the result indi-
cated with the Analog Status Flags. If the result is outside the set range, the
Normal Flag (pass signal) is turned ON.
Off-wire Detection
With Analog Input Terminals, disconnections can be detected in wiring for
analog (voltage or current) inputs that are enabled as AD conversion points.
Содержание SMARTSLICE GRT1-DRT
