![background image](http://html.mh-extra.com/html/omron/nt15s/nt15s_operation-manual_744537153.webp)
139
Standard Mode
Section 4-9
System Message 11 . . . .‘Interface in use’
SER2 is already being used by another print job. An attempt has been made to
transmit different types of data to the printer at the same time (e.g. to print recipes
and messages).
System Message 12 . . . .‘Invalid Password’
The operator has entered a password which does not exist in the password list.
With this message, the previous access authorizations (view and edit level) are
reset.
System Message 13 . . . .‘Password unchanged’
The operator did not enter the same new password two times in a role.
System Message 14 . . . .‘Overvoltage’
The system has detected that the supply voltage is too high. Switch the terminal off
immediately to avoid damage. Check supply voltage.
System Message 15 . . . .‘Data set protected’
An attempt has been made to modify individual values of a data set stored in the
flash or to delete the entire data set.
System Message 16 . . . .‘Illegal data set’
The data set number specified as the destination for the data set copy process
exists already or is outside the valid range (for example, flash).
System Message 17 . . . .‘Data set unknown’
A data set has been selected whose number does not exist in the data set list.
System Message 18 . . . .‘Data set memory full’
An attempt has been made to create a new data set, but the data set memory is full.
System message 19 . . . .‘Data set active’
An attempt has been made to erase or to copy to the active data set or to select a
data set even though the active data set is currently being edited.
System Message 20 . . . .‘Data set transfer’
An attempt has been made to initiate a data set transfer to the controller even
though the previously initiated transfer has not yet been completed.
System Message 21 . . . .‘Password missing’
An attempt has been made to switch to a password-protected mask or to edit a
password-protected mask without having entered a password with sufficient au-
thorization.
System Message 22 . . . .‘Editing mode active’
An attempt has been made to perform a change of mask while the terminal was in
the editing mode.
System Message 23 . . . .‘Data set file error’
The data set file loaded from the PC to the terminal contains a syntax error. The
error can be localized by means of the line number system variable.
Содержание NT15S
